Elkay LZWSRK-EZH2O Installation & Use Manual Download Page 18

Page: 18 / 19

Page 18

EZWSR*1C, *2C LZWSR*1C, *2C

1000001734 (Rev. K - 04/18)

2.25

2.00

3.75

1.75

1-3/8" Dia. Hole

3/8" Dia. Pilot Hole

3/16" Dia. Hole

Bottom View of Cooler

Fig. 18

Alternate Filter Mounting Location Fig. 19

SCREWS

PLASTIC BUSHING

SCREWS

FILTER MOUNTING BRACKET

FILTER ASSEMBLY

ALTERNATE FILTER MOUNTING LOCATION

1) Drill one 3/8” diameter pilot hole “A” as shown in Fig. 18.

2) Using the 1-3/8” dia. punch supplied with 98552C Kit - Retro Filter Mounting, punch a 1-3/8” dia. hole “A” at the 3/8” pilot hole, see Fig. 18.

3) Drill two 3/16” dia. hole at location “B” shown in Fig 18.

4) Remove Filter bracket from filter assembly and reinstall as shown in Fig. 19. Be sure the 3/8” water inlet is facing out.

5) Install plastic bushing (supplied) as shown into 1-3/8” hole, bushing must be used so waterlines will not be cut by sharp edges of base plate.

6) Install filter assembly to bottom of cooler as shown in Fig. 19 with 2-#8 sheet metal screws.

7) Run the inlet and outlet water lines to filter.

8) Use P/N 98551C KIT- LZ Filter Mounting Cover (Light Gray Granite), or P/N 98568C KIT- LZ Filter Mounting Cover (Stainless Steel), may be

order to enclose the filter beneath the cooler (Not Shown).

3/8” WATER INLET

Summary of Contents for LZWSRK-EZH2O




















Search results

Summary of Contents for LZWSRK-EZH2O

Reviews:

Related manuals for LZWSRK-EZH2O

Brands by name

Popular brands

Elkay LZWSRK-EZH2O, Installation & Use Manual

Search results

Summary of Contents for LZWSRK-EZH2O

Reviews:

Related manuals for LZWSRK-EZH2O

Brands by name

Popular brands