Page 3
1000002684 (Rev. C - 07/19)
EZS8WS_2G, LZS8WS_2G, LZSDWS_2G
Figure 1
Installation: Bottle Filler Mounting
Remove two (2) mounting screws with 5/32” Allen wrench
holding top cover to Bottle Filler. Remove top cover. Note:
do not discard mounting screws; they will be needed to
reinstall top cover. (See Fig. 3)
Remove wall mounting plate from Bottle Filler. Place wall
plate against wall on top of basin. Center the wall plate side
to side with the basin. Mark the six (6) mounting holes with
a pencil (See Fig.1).
Remove wall mounting plate from wall. NOTE: Mounting
plate MUST be supported securely. Add fixture support car
-
rier if wall will not provide adequate support.
Install wall mounting plate to wall using six (6) 7/16” oval
mounting holes (mounting bolts not included) (See Fig. 2).
Use appropriate fasteners for your wall type.
Feed 3/8” water line through hole in tower/basin gasket
(See Fig 4).
Install gasket on bottom of bottle filler tower with gasket
support bracket & (2) screws (See Fig 5).
Feed modular (C-13) end of International Power Cord Set
up through basin hole and hole in gasket, and connect to
Power Inlet on Bottle Filler. Do not plug into electrical outlet.
Lay Bottle Filler on water cooler basin and cut insulation
from tube even with bottom of gasket, remove this insulation
from the 3/8” tube, but do not discard. Feed the waterline
through the hole on top of water cooler. NOTE: To prevent
scratching the basin, place a towel or soft cloth over the
entire basin when working above it.
1.
2.
5.
3.
4.
7.
6.
8.
Figure 2
Figure 3
Figure 4
Figure 5
Bracket & Screws
F
E
A
B
7/
1
6
" X 3
/
4"
O
BR
O
UND
(11mm X 1
9
mm) H
O
LES (
6
)
C
D
E
9/
32"
O
H
O
LES
(
7
mm) (12)
FINISHED FL
OO
R
L
C
7
"
1
7
8mm
7
"
1
7
8mm
1
7
7/
8"
454mm
6
3
/
8"
1
6
2mm
6
3
/
8"
1
6
2mm
2"
51mm
2"
51mm
5 3
/
4"
14
6
mm
13 15
/
1
6
"
354mm
1
7
7/
1
6
"
443mm
1
9
"
483mm
28 13
/
1
6
"
7
32mm
51
9/
1
6
"
1310mm
18
7/
8"
4
79
mm
12 1
/
2"
318mm
31 5
/
1
6
"
796
mm
RI
M
HEIGHT
32
7/
8"
835mm
O
RIFICE
HEIGHT
21
7/
8"
55
6
mm
2"
51mm
3
7/
8"
9
8mm
7
"
1
7
8mm
7
"
1
7
8mm
28 13
/
1
6
"
7
32mm
2"
51mm
2
7/
8"
7
3mm
15"
381mm
2
7
"
6
8
6
mm
ADA
REQUIRE
M
ENT
8 1
/
1
6
"
205mm
1
9
"
483mm
3
9/
1
6
"
9
0mm
5
7/
8"
150mm
3"
77
mm
2"
51mm
38 1
/
2"
979
mm
ACTIVATI
O
N
SENS
O
R
HANGER BRACKET
Rough-In: LZS8WSS2K
7/16” BOLT HOLES FOR
FASTENING UNIT TO WALL
UNIT CENTER LINE
TOP COVER
MOUNTING
SCREWS
29
A = Water Mains Supply, 3/8” (9.5mm) O.D. compression outlet of Shut-off Valve (not provided) to be 3” (76mm) from Wall.
B = Waste Outlet, 1-1/4” (31.8mm) O.D. Drain tube terminating 2” (51mm) maximum from wall.
C = 1-1/4” (31.8mm) Trap (not provided).
D = Electrical Mains Supply Outlet, 3-wire in Recessed Box. Must have Ground Fault Circuit Interrupter (GFCI) protection.
E = Ensure proper ventilation by maintaining 6” (152mm) minimum clearance from cabinet louvers to wall.
F = 7/16” (11mm) Bolt holes for fastening unit to wall.
