PAGE 4
FD700_3_2JJO, FD700_5_2JJO
1000003126 (Rev. A - 12/15)
Service: Inspection/Cleaning
• Inspect Cooler twice each year for proper operation and performance.
• Inspection of the unit will require disconnecting electrical supply, removal of panels, etc.
and reassembly and return to service practices.
1. Cleaning: Warm, soapy water or mild household cleaning products can be used to clean the exterior panels. Extra caution should be used to clean
the mirror finished stainless steel panels. They can be easily scratched and should only be cleaned with mild soap and water or Windex glass
cleaner and a clean, soft cloth. Use of harsh chemicals or petroleum based or abrasive cleaners will void the warranty.
2. Bubbler
: Mineral deposits on the orifice can cause water flow to spurt or not regulate. Mineral deposits may be removed from the orifice with a
small round file not over 1/8” (3 mm) diameter or small diameter wire.
• CAUTION
: DO NOT file or cut orifice material. Care must be taken not to damage the orifice(s)
3. Condenser Fan Motor
: Confirm condenser fan turns freely. If the condenser fan does not spin freely, have an authorized service personnel
replace.
4. Ventilation
: Cabinet louvers and condenser fins should be periodically cleaned with a brush, air hose or vacuum cleaner. Cleaning should be done
twice each year or more frequently if needed due to environment. Excess dirt or poor ventilation can cause no cold water and compressor cycling
on the compressor overload protector.
5. Water Flow
: Confirm proper water flow. If water flow is slow, inspect filter or inline strainer for restriction. Replace filter cartridge if required.
Disassemble inline strainer and clean if required See Figure 6.
6. Lubrication: Motors are lifetime lubricated.
7. Actuation of Quick Connect Water Fittings: Cooler is provided with lead-free connectors which utilize o-ring water seal. To remove tubing from the
fitting, relieve water pressure, push in on the gray collar before pulling on the tubing. To insert tubing, push tube straight into fitting until it reaches
a positive stop, approximately 3/4” (19mm). See Figure 7.
Service: Inspection/Replacement
• Inspect Cooler twice each year for proper operation and performance.
• Inspection of the unit will require disconnecting electrical supply, removal of panels, etc. and reassembly and return to service practices.
1. Bubbler
: To remove the bubbler, first disconnect the electrical supply. Remove the Front Panel by removing (2) screws. To remove the bubbler,
loosen locknut from the underside of the basin and remove the tubing from the quick connect fitting (see Figure 7 for actuation of Quick Connect
Fittings). When installing replacement bubbler, tighten nut only to hold parts snug in position. Do Not Overtighten. After servicing, replace the
front panel and two (2) screws.
2. Cleaning Strainer
: Restricted water flow may be caused by clogged screen. Remove plug and screen. Clean screen and replace. Lubricate
O-Ring with food grade pharmaceutical mineral oil. Do not overtighten plug or fittings. See Figure 6.
A
C
B
D
A = Plug with 7/8" (22.2mm) Hex
B = O-ring
C = Screen
D = Strainer Body with 1" (25.4mm) Hex
Figure 6
Figure 7
Figure 4
Figure 5
Figure 8
- When provided
6
5
4
3
1
7
2
8
ITEM
NO.
Filter Head Ass’y
Screw #8-18 X .75 PH
Fitting - Superseal 3/8”(10mm)
Fitting - Superseal 1/4” (6mm)
Filter Ass’y
Elbow - 3/8” (10mm)
Elbow - 1/4” (6mm)
Bracket
1
2
3
4
5
6
7
8
51294C
70792C
70823C
70822C
51299C
70818C
70817C
22490C
DESCRIPTION
PART
NO.
WATERSENTRY
®
FILTER PARTS LIST
(See Fig. 3)
BASIN
1
COVER NUT
BUTTON
2
BASIN
8
Locknut