Elk M1XRFTW Installation Manual Download Page 10

Page: 10 / 16

Page 10

M1XRFTW Installation Manual

Wireless Submenu

Description

This submenu is for Receiver options. To select this menu press the RIGHT arrow key, or
press the Up or Down arrow keys to scroll the submenus.

Rec. Option R03 is the time value for zones programmed as Supervisory Type 1 or "Non-Fire"
transmitters (see Xmit Transmitter Opt 02 below). The range is 001 to 255 hours. If a Type 1
sensor fails to check-in prior to the expiration of this time it is considered "missing". Factory
default setting is 024 hours. NOTE: A value less than 4 hours is NOT RECOMMENDED!

Rec. Option R04 is the time value for zones programmed as Supervisory Type 2 or "Fire"
transmitters (see Xmit Transmitter Opt 02 below). The range is 001 to 255 hours. If a Type 2
sensor fails to check-in prior to the expiration of this time it is considered "missing". Factory
default setting is 004 hours. NOTE: A value less than 4 hours is NOT RECOMMENDED!

This submenu is for specific transmitter options. Some options are not applicable to this
model of the M1XRF. To select this menu press the RIGHT arrow key, or press the Up or
Down arrow keys to scroll the submenus.

Use the UP and DOWN arrow keys to locate a particular wireless transmitter. Press the
RIGHT arrow key to select and program the displayed transmitter.

Displays whether a transmitter is enabled or disabled. This option CANNOT be used to add a
new device, but it can be used to temporarily suspend an already enrolled device. The enroll
process must be used to add a new transmitter, after which this location will be set to Yes.

Supervision type sets the expected check-in interval of a sensor. KeyChain Remotes (Fobs)
or devices which may leave the building program set this "0" = non supervised. Burglar
Sensors should have this option set as "1"=Normal Supervision. Fire Sensors should have
this option set as "3" = HI Supervision. See receiver selections R02 and R03 for supervision
time values. Valid values are: 0, 1, or 3 Factory default setting is 1 (Normal Supervision).

Pertains only to certain types of Transmitters. For KeyChain Remotes setting this option to
Yes converts buttons 1,2,3,4 to be instead buttons 5,6,7,8. Default is No.

See list of

compatible Transmitters to determine which (if any) transmitters use this option.

Pertains to transmitters with Ext. contact terminals. Setting this to Yes permits Open Circuit
[N/O] switches. If set to No then only Closed Circuit [N/C] switches may be connected.
Default is No.

See list of compatible Transmitters to determine which (if any)

transmitters use this option.

Used to program the User ID which will be logged when a Keychain Remote assigned to this
zone is used to arm of disarm. Valid range is 001 to 255. Numbers 001 to 199 mirror keypad
user codes. Note: Open/Close reports may be programmed for every User code.

Not used. If set to Yes the zone is auto-restored to normal in 8 seconds with no restoral
signal from the transmitter.

1234567890123456789012345678901212345

1:Rec Sel

Prg

Receiver Options

There are four (4) wireless setup submenus: 1-Receiver Options, 2-Xmitter Options, 3-Xmitter
Enroll, and 4-Keyfob Event Definitions. Use the UP or DOWN arrow keys to locate the desired
submenu, then press the right arrow key to select.

12345678901234567890123456789012123

1 4 - W i r e l e s s
Setup

†

Not evaluated by UL

123456789012345678901234567890121234

2:Xmit Sel

Prg

Transmitter Opt

1234567890123456789012345678901212345

WZn017 04: = No

Enable Option 2

123456789012345678901234567890121234

WZn017 01: = No

Enable Transmitr

1234567890123456789012345678901212345

WZn017 02: = 0

Supervision Type

1234567890123456789012345678901212345

WZn017 03: = No

Enable Option 1

1234567890123456789012345678901212345

RO3:=024 Hours

Reg. Supervision

123456789012345678901234567890121234

WZn017:Sel

Prg

Wireless Zone

1234567890123456789012345678901212345

WZn017 05: = 001

Keyfob User ID

123456789012345678901234567890121234

WZn017 06: = No

PIR Auto Restore

1234567890123456789012345678901212345

RO4:=004 Hours

Fire Supervision

From the keypad enter the Installer Level Programming mode. Press ELK, 9 > (enter installer code).
Navigate to the Wireless Setup - Menu 14 and press the RIGHT arrow key to select.

Detailed Keypad Programming

< continued on next page >

WZn017 shown as an example only!