Elk Products EZ8 ELK-M1EZ8 Installation Manual Download Page 39

Page: 39 / 68

M1EZ8 Installation and Programming

Page 39

Area Report Codes

Description of Option

Duress code will be reported if the area is armed or disarmed by a valid user code that is
programmed with the duress attribute. Range is 00 to FF. Default is 00 (no report).

Open After Alarm code will be reported whenever a valid user arrives and disarms the area
following an alarm activation. Range is 00 to FF. Default is 00 (no report).

Open Early code will be reported if the area is disarmed prior to a programmed Expected
Disarm time. Refer to the ELK-RP Rules Programming instructions. Range is 00 to FF.
Default is 00 (no report).

Fail to Open code will be reported if the area is not disarmed by a programmed Expected
Disarm time. Refer to the ELK-RP Rules Programming instructions. Range is 00 to FF.
Default is 00 (no report).

Open Late code will be reported if the area is disarmed after a programmed Expected
Disarm time. Refer to the ELK-RP Rules Programming instructions. Range is 00 to FF.
Default is 00 (no report).

Open Keyswitch code will be reported in place of a user code whenever the area is
disarmed by a Keyswitch zone. Range is 00 to FF. Default is 00 (no report).

User Lockout code will be reported if someone repeatedly enters digits (see Menu 07 -
Global System Definitions, Option 12 for the maximum number of digits allowed) in an
attempt to hack out a valid user code. Range is 00 to FF. Default is 00 (no report).

Exit Error Code can be used to identify an accidental alarm caused by an error while
arming. Locally, it works as follows: If an exit delay rolls directly into entry delay as a
result of a zone being left violated, the entry delay warning AND the siren will sound. If the
control is not disarmed prior to the entry delay expiring, the communicator will report the
alarm along with the Exit Error code. Range is 00 to FF. Default is 00 (no report).

Fail to communicate displays on the keypad and the event log when the communicator
fails to complete it’s report using the number of dial attempts. A good communications
report must occur in order to reset/clear the failure. If this fail to communicate report code
is enabled, it will be reported with next good communications to indicate a “past” failure.
Range is 00 to FF. Default is 00 (no report).

12345678901234567890123456789012123

AR1 13:Code= 00

Open Early

12345678901234567890123456789012123

AR1 14:Code= 00

Fail To Open

12345678901234567890123456789012123

AR1 15:Code= 00

Open Late

Menu 09 - Area Reporting Codes

(continued)

12345678901234567890123456789012123

AR1 16:Code= 00

Open Keyswitch

12345678901234567890123456789012123

AR1 17:Code= 00

User Lockout

12345678901234567890123456789012123

AR1 18:Code= 00

Exit Error

12345678901234567890123456789012123

AR1 19:Code= 00

Fail Communicate

12345678901234567890123456789012123

AR1 11:Code= 00

Duress Code

12345678901234567890123456789012123

AR1 12:Code= 00

Open After Alrm

Area RCs

CID

SIA

Alarm Abort

406

O C

Alarm Cancel

406

O C

Automatic Close

403

C A

Early Close

451

C K

Closing Extended

464

C E

Fail To Close

454

C I

Late Close

452

C J

Key Switch Close

409

C S

Duress

121

H A

Area RCs

CID

SIA

Open After Alarm

450

O R

Early Open

451

O K

Fail To Open

453

O I

Late Open

452

O J

Key Switch Open

409

O S

Keypad Locked Out

461

J A

Exit Error

457

E E

Fail To Communicate

354

R T

Based on the event, the CID (Contact ID) or SIA Codes for Area Reporting Codes will be:

NOTE: On CID reporting the 3 digit code will be preceded by a “1” for a new event or
an opening. It will be preceded by a “3” for a restore or a closing event.