background image

042717DR 

www.elitescreens.com 

   

 

 

Aeon CLR® Series 

EDGE FREE

 

CLR®

 

Fixed Frame Screen   

w/ StarBright CLR® (Ceiling Light Rejecting®) Front Projection Material 

User’s Guide 

 

Product Description: 

The 

Aeon  CLR®  Series 

is an  ultra-short throw  fixed frame projection screen that uses Elite’s EDGE FREE

 

CLR®

 

technology.  It is designed for  with 

Ultra

-

Short  Throw Projectors  only, 

for use in environments where ceiling  light 

cannot be entirely controlled

It includes an LED backlight kit and a bezel trim to further enhance the frame appearance. 

 

Screen Maintenance 

Dust, dirt and scratches on the projection screen surface will affect the quality and performance of the projection image. 

For optimal results we advise to pay attention to the following instructions.

 

1) The screen surface has a horizontal structure. 

DO NOT

 wipe the screen up and down or in a circular motion.   

Wipe from left to right only

2) Please clean the dust on the screen surface with a soft brush or microfiber cloth (rough towel or cloth may damage 

the screen’s surface). 

3) Gently wipe the screen with a moistened microfiber cloth with mild soap diluted in water. 

Notes

 

The following precautions should be followed at all times to avoid damaging the material, which is not 
covered under warranty. 

 

Don’t 

touch

 the screen material to avoid leaving fingerprints. 

Use gloves when handling the material

 

Don’t 

scratch

 the material, as it will leave permanent markings on the screen’s surface. 

 

Don’t 

point 

to the screen material with a fingertip or other sharp objects to prevent damage to the material. 

 

Don’t use acetone, benzene, alcohol and any other organic solvents to clean the screen material. Using such 

chemicals will permanently damage the screen. 

 

Assembly Video   

 

 

 

Watch our assembly video on-line at 

www.elitescreens.com/aeonCLR_assembly 

or scan the QR code

 

 

 
 

Summary of Contents for aeonclr series












Reviews: