5.2
. GARAGE GATE CONTROL.
In
case your garage gate control system is compatible with 'ELITA’ type alarm systems. You can open
or close garage gate by pressing button
.
or
button can be used for entrance gate control.
6. SERVICE MODE.
6.1. TURNING SERVICE MODE ON.
'ELITA E50' features service mode for emergency
such
as loss of remote control or car repairs.
With this mode on alarm system does not respond to sensors, does not immobilize the engine, and does not signal. System LED bursts
frequently. Service mode is turned ON using the PIN code.
6.2. ENTERING THE PIN CODE.
Open vehicle doors and turn the ignition ON. Shortly after when system LED starts bursting double
flashes, count till the number of double flashes corresponding with digit 1 of the PIN code. Turn the ignition OFF for a short time and turn
it ON again. Count double flashes till the number corresponds with digit 2 of the PIN code. Turn the ignition key OFF and ON again. Enter
the remaining two digits of the PIN code respectively. Upon correct entry of all four digits of the PIN code, LED fires triple flashes for 12
seconds progressing into frequent light bursts. If you have made a mistake during the entering the PIN code, turn OFF the ignition, close the
doors and start article 6.2 steps all over again. Service mode is turned OFF by pressing button
or by entering code FN=11
.
6.3. CUSTOMIZING THE PIN CODE.
A user is provided with possibility of changing PIN code. This requires:
a) Enter current PIN code;
b) Wait for 13 seconds until system LED starts flashing rapidly;
c) In the same manner as with PIN code entering, enter 2 - digit code 88. The entry will be confirmed by short flash of direction
indicators;
d) Within 8 minutes enter the new PIN code twice, one after another. If in both cases the same code is entered, the system will
record this as the new PIN code and confirm it by short flash of direction indicators.
6.4. PROGRAMMING REMOTE CONTROLS.
After
entering the PIN code system LED flashes with triple flashes for 12 seconds. You
can pre-program remote control within this time period. Press the remote buttons
,
and hold them down (approximately 4 seconds)
until long flash of system LED. First remote control is pre-programmed; pre-programming time frame is extended to additional 12 seconds
for another remote control. After pre-programming of the first remote control all previous remote controls are deleted from the alarm system
memory.
6.5. INFORMATION ON PRE-PROGRAMMED REMOTE CONTROLS.
Since
it is possible to pre-program from 1 to 5 remote
controls,
'ELITA E50'
user has the ability to check the number of pre-programmed remote controls. To do that disarm the system, press
button
and count the
number
of system LED flashes. The number indicates number of units (remote controls) controlling the system.
7. ADDITIONAL FUNCTIONS.
7.1.
INNER IMMOBILIZER.
With
inner immobilizer turned ON, every time after 40 seconds since turning the ignition OFF, system LED
starts flashing with long flashes and subsequent start up of the engine is possible only by pressing button
.
With immobilization
disabled
system LED stops flashing. Alarm system can be wired and set in a way it is possible to control inner immobilization using secret button
rather than button
.
In
case of the latter to turn OFF engine immobilization press secret button immediately
after
disarming security or
after 40 seconds after turning the ignition OFF.
7.2. CONTROLLING INNER IMMOBILIZER FUNCTION.
In
case inner immobilizer function is creating undesirable inconveniences, it
is possible to turn it OFF temporarily. Execute the following: disarm the system, turn the ignition ON, press at the same time buttons
and
and hold them
down for 5 seconds till short chirp of the siren. To turn the function ON repeat the same thing.
7.3. PROTECTION AGAINST OPEN THEFT ('ANTI-CARJACK').
The
function is possible to select if vehicle is operated outside the
EU countries. Description of the function: with opened door and ignition ON press a secret button (pressing confirmed by long LED flash),
otherwise the alarm fires within 40 seconds, direction indicators start flashing and within another 10 seconds the engine shall be immobilized
and security system turned ON (setting FN=23, SN=2) or the engine is immobilized just after tuning the ignition OFF with subsequent
system arming (setting FN=23, SN=1). Alarm and engine immobilization can be cancelled only by pressing a secret button. Depending on
the settings the mentioned function can or cannot be turned OFF by using remote control. To turn OFF the function disarm the system, turn
the ignition ON, press a secret button when
press together buttons
and
. Hold the button pressed for 5 seconds till short chirp of the
siren. To turn the function ON repeat the same thing.
7.4. ARMING WITHOUT USING A REMOTE CONTROL.
Usually this function is selected in case of frequent thefts made by using
radio noise devices or in case a user does not trust remote-controlled alarm systems. With the function activated and ignition OFF vehicle
driver has to take the keys with him, press the secret button twice, open the doors, get out of the vehicle, and close the doors. Alarm system
will automatically arm and enable central lock. System is disarmed in the usual way, i.e. using remote control.
7.5. WARMING-UP THE ENGINE .
The
function is possible to select if vehicle is operated outside the EU countries. Description of the
function: with engine turned ON press a secret button twice, get out of the vehicle and press remote control
button
.
Alarm system is
armed, central lock enabled. The system will not respond to sensors however in case of door, engine hood or luggage compartment opening,
the siren starts sounding and direction indicators flashing. 10 seconds after the system blocks engine operations and turns the alarm system
ON again (setting FN=23, SN=2), or the engine is immobilized just after turning the ignition OFF (setting FN=23, SN=1). System is
disarmed in the usual way, i.e. using remote control.
7.6. AUTOMATIC REARMING.
Security
system is automatically activated in case vehicle door, engine bonnet or luggage compartment
opening or engine turn ON have not occurred within 45 seconds after the system disabling. The doors are not to be locked!
Alarm system can be to set to lock the doors during auto-rearming or to turn OFF the auto-rearming completely.
7.7. AFTER ARMING THE SYSTEM
does not respond to vehicle door, engine bonnet or luggage compartment opening and vibration or
volume sensors for predefined period of time (factory setting of 5 seconds, can be set to 45 seconds). If the siren signals 3 times after the
time has elapsed and the alarm is ON,
this indicates that vehicle doors, engine bonnet or luggage compartment are not closed properly. The
doors are locked!
7.8. UPON DISARMING THE ALARM DIRECTION INDICATORS FLASH
4 times if the system had alarmed when enabled.
8. WARRANTY STATEMENT.
8.1. MANUFACTURER AND DISTRIBUTOR OF ALARM SYSTEM 'ELITA E50'
accepts no liability for possible vehicle theft.
8.2. WARRANTY TERM FOR VEHICLE ALARM SYSTEM 'ELITA E50' IS 24 MONTHS,
warranty
term being calculated from the
day of the purchase. If no original receipt is available, the term starts from the day of alarm system manufacturing (indicated on the
Identification label). Warranty does not cover end switches, state indicator, remote control casings and batteries. Warranty becomes void in
case of any modifications; incorrect installation; misuse; mechanical, chemical, and electrical damage; in other cases having no relation to
manufacturing faults of the alarm system.
In case the alarm system gets out of order or operates incorrectly, please contact the installer of your alarm system for all warranty and
post - warranty service. Practice shows that in most cases alarm system operates incorrectly because of improper installation or vehicle
defects. Manufacturer of the alarm system – KODINIS RAKTAS – does not provide consultancy on issues of installing or operations of
alarm systems. For more details on manufacturer, products and FAQ visit Internet website at
www.kodinis.lt
.
Vehicle alarm system 'ELITA E50' is being manufactured in Lithuania in compliance with the corporate standard ÁST2365999 - 02:2004.
I
M
M
I
I
I
I
M
I
M
I
M
