background image

 

 

 

ELIS PLZEŇ a. s.

 

Project design, installation and service manual 

 

Page 11 o

f

 33 

Electromagnetic flowmeters of the type series  

FLONEX FXx11x and FLONET FH30xx 

Meter control instructions 

 

ELIS PLZE

Ň a. s., Lucni 425/15, 301 00 Plzeň, Czech Republic  tel.:+420 377 517 711, fax:+420 377 517 722  

Es 90 686 K

 

 

5.1.4.2.1. 

Display data 

Upon  selecting  the 

Display  data

  item,  the  user  may  pick  out  supplementary  data  to  be  shown  on  the 

display lines 3 and 4. In Basic screen, these appear under the data on current/instantaneous flow rate. The 
initial  setting  consists  of  the  data  on  the  aggregate  flow  volume  passed  through  the  meter  sensor  in  the 
positive and negative directions.  

 
 
 
 
 
 
 
 
 
 
 
 
 
 

The item selected by buttons 

► and ▲ will be highlighted (in yellow). Confirm the selection by 

ENTER

, the 

display  will  then  return  to  the  previous  menu  item.  The  selected  item  will  appear  on  line  four  in  Basic 
screen. Displayed can only be one item at a time. 

 

 Upon selecting the 

No display

 item, Basic screen will only show the instantaneous flow rate data 

(line 1 … flow rate, line 2 … flow rate units). 

 

5.1.4.2.1.1  Volume 

Q+ a Q− 

Alternated (cyclic) display of current flow volume and the selected volume unit:

 

 

Display line 3: aggregate flow volume passed through the meter in positive direction 

 

Display line 4: aggregate flow volume passed through the meter in negative direction  

 

5.1.4.2.1.2  Time and date 

Display line 3: time 
Display line 4: date  

 

5.1.4.2.1.3  Working time and error time 

Display line 3: measurement down time due to meter error (Error time) 
Display line 4: aggregate operating time (Working time) including Error time 
 

5.1.4.2.1.4  Excitation current 

Display line 3: current flowing through the sensor excitation coils (typically 200mA) 
Display line 4: resistance of the fluid between the measuring electrodes (kΩ). This information is 
used to check the condition of fully flooded piping. 

 
5.1.4.2.1.5  Flow rate per cent 

Display line 3: measured flow rate in per cent of the maximum flow rate 
Display line 4: the character of % 

 

 

Total volume 
Date/time 
Working time 
Excitation current 
Flow rate per cent 
Last error 
No display 

Display data 
 
 
Total volume

 

 

To  move  downward  in  the  menu,  use 

button 

 

 

ENTER 

To  move  upward  in  the  menu, 
use button 

▲ 

 

Summary of Contents for FLONET FH30xx Series


































Reviews: