ELICA NIKOLA TESLA FLAME, Instruction On Mounting And Use Manual, Page: 74 / 387

73
USING THE HOB
The burners are ignited by pressing the corresponding knob
(1) and turning the knob in an anti-clockwise direction, until
the mark coincides with the maximum position
The electric discharge between the igniter and the burner
lights the burner in question. When lit, immediately release the
knob and adjust the flame as required.
The burner is ignited by keeping the knob fully pressed in the
maximum position for about 3/5 seconds. When releasing the
knob, make sure that the burner stays on.
NB = in the event of a power failure, the burner can be lit by
turning the knob in the same way and placing a small flame
close to the holes in the upper part of the burner.
The Dual burner is ignited in the same way, by pressing and
turning the corresponding knob (2).
For this type of burner, it is possible to turn on the central
flame (F1) by turning and pressing the knob clockwise, or turn
on the entire burner (F1 + F2) by turning and pressing the
knob anti-clockwise.
USING THE EXTRACTOR FAN
NB = the extraction fan knob has back-lit dial;
depending on the function to be performed, the knob can be
turned or pressed.
•To select the extraction speeds available:
Turn the knob (3) clockwise to switch on and increase the
extraction speed and anti-clockwise to decrease it, and turn
off the hood.
The crown (L) lights up to indicate the chosen extraction
speed:
•L1 on
speed 1
•L1+L2 on
speed 2
.•L1+L2+L3 on
speed 3
•L1+L2+L3+L4
-flashing slowly
speed 4 (boost 1): Duration 30 minutes after which the hood
is automatically set to speed 3
•L1+L2+L3+L4
-flashing rapidly
speed 5 (boost 2): duration 7 minutes, after which the hood is
automatically set to speed 3
•L off:
Extraction motor off
•Timer
The extraction fan has a timer function for automatic timed
switch-off.
NB = there is no timer for Boost 1 and Boost 2 speeds, which
are already timed
To activate the timer, press the knob (3-T) for 2 seconds;
- if you are using speed 1: the hood will automatically switch
off after 15 minutes (L1 flashes)
- if you are using speed 2: the hood will automatically switch
off after 10 minutes (L1 is fixed
–
L2 flashes)
- if you are using speed 3: the hood will automatically switch
off after 5 minutes (L1+L2 are fixed - L3 flashes)
•Filter saturation check device
The hood is fitted with a device that signals when the filters
require maintenance
To activate the filter saturation check device, proceed as
follows:
1 - Switch off the hood.
2 - Press the knob (3-T), for 5 seconds;
The crown (L) turns on fully and flashes, indicating that you
have entered the filter settings menus
NB = the anti-grease filter saturation check device is usually
already enabled;
The active carbon filter check device is usually disabled
3a -Anti-grease filter
Turn the knob (3) clockwise, L2+L3 are on and fixed
Press the knob: L2 +L3 start flashing, the anti-grease filter
check device is disabled
Press the knob: L2 +L3 stop flashing and become fixed, the
anti-grease filter check device is enabled
3b -Active carbon filters
Turn the knob (3) anti-clockwise L1+L4 are on and flashing
Press the knob: L1 +L4 stop flashing and become fixed, the
active carbon filter check device is enabled
Press the knob: L1 +L4 start flashing, the active carbon filter
check device is disabled