43
authorised dealer or technical assistance centre.
Automatic operation of the hood with SNAP
®
and Elica
hob
Press the button
.
(the LEDs
light up in
orange) to indicate that the hood can operate automatically
with the hob and the
SNAP
®
Setting of parameters for Automatic Operation
Note:
All calibration, selection, setting and logical
connection operations described below can be performed
with the hood off (OFF).
The adjustment of parameters is regularly done
automatically
every time the hood is reconnected to the
mains (e.g. with the first installation or after a blackout) or
manually
.
Manual setting
To be performed when you notice unsatisfactory
functioning of the Automatic operation, and is done when
normal environmental conditions persist in the kitchen.
Manual setting includes:
• Hood
calibration
•
Selection of hob (gas, induction, or electric)
•
Logical connection between the hood and
SNAP
®
(if
you have
SNAP
®
).
Hood calibration
Press and hold the button
, all button LEDs
flash to indicate initiation of calibration; the process
will last for approximately 5 minutes.
Selection of the hob
(gas , induction, or electric)
Press and hold simultaneously the buttons
and
: buttons
,
and
start flashing for 5 seconds.
Within this timeframe,
press:
button
in case of gas hob
button
in case of electric hob
button
in case of induction hob
The preselected button remains lit to indicate the
selection was performed, after 10 seconds the
button flashes briefly to indicate that the performed
selection was recorded.
Logical connection between the hood and SNAP
®
(if
you possess a SNAP
®
).
Connection between the hood and SNAP
®
is
automatic. No other setting has to be performed.
Control panel with 6 buttons
Automatic operation (sensor) e
connection with SNAP
®
Button ON/OFF lighting
Press briefly to turn on or off the hob
lighting.
Press and hold to adjust the tonality
of light.
Button to select high speed
(suction power)
:
- first
touch
Button to select intensive speed
(suction power)
:
- second
touch
Intensive speed (suction power) has
a duration of 5 minutes, then the
hood returns to medium speed
(suction power); the button flashes.
Note:
pressing again the hood goes
back to high speed (suction power).
Button to select medium speed
(suction power)
:
-
Button to select low speed
(suction
power)
:
- when flashing, it indicates
you must wash the grease filter.
Button OFF motor
(stand by)
Filter Saturation Indicators
At regular intervals the hood signals the need to perform filter
maintenance.
Button on continuously: perform maintenance of
grease filters.
Button on with flashing light: perform maintenance
on the activated charcoal filter
Note:
The filter saturation indicator is visible within the
first minute after the hood switching off; the reset of
Summary of Contents for Bio
