background image

 
 
 
 

 

 

17

 

16. Liability exclusion / Guarantee 

We have checked the contents of this instruction manual carefully, to the best of our knowl-

edge and belief for conformity with the described hardware and software. Nevertheless errors, 

mistakes or deviations can not be excluded, therefore we do not guarantee complete confor-

mity. Necessary corrections will be included in the subsequent editions.  

We appreciate your ideas and improvement suggestions very much. Reprint, duplication and 

translation, even in extracts, are only allowed with a written authorization by the company 

ELGO Electronic GmbH & Co. KG. We constantly strive for improving our products, therefore we 

keep all rights reserved for any technical modifications without any notice. ELGO Electronic 

GmbH & Co. KG does not assume any liability for possible errors or mistakes. 

 

The guarantee period is one calendar year from the date of delivery and includes the delivered 

unit with all components. ELGO Electronic GmbH &  Co. KG will at its option replace or repair 

without charge defects at the unit or the included parts, verifiable caused by faulty manufac-

turing and/or material in spite of proper handling and compliance to the instruction manual.  

 

Damages verifiably not caused by ELGO Electronic GmbH & Co. KG and due to improper han-

dling are excluded from any guarantee e.g. by applying faulty voltage, diffusion of liquid into 

the interior of the engine, using force, scratching the surface, 

chemical influences etc.!

  

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

Dok.- Nr. 799000082                 
Z58-000-E_07-10                  
Subject to modifications - 

©

  2010 - ELGO Electronic GmbH & Co. KG

 

Summary of Contents for Z58-6 Series


















Reviews: