background image

15P0056B1

APPLICATION MANUAL     

AMS90/1

  

8/17

SIZE CODES AND EXTRA-QUICK FUSES TABLE

SIZE CODES AND EXTRA-QUICK FUSES TABLE

Drive

Product

code

Size

code

Max.

mean

curr.

(A)

Max.

allowed

form

factor

F.A.

fuses

FU1/2

(A)

Max I

2

T

for FU1/2

V

A L I M

 

+10%

(A

2

s)

AMS90/1.10 supp.230V

ZZ0045020

01230

AMS90/1.10 supp.400V

ZZ0045020

01400

AMS90/1.10 supp.415V

ZZ0045020

01410

AMS90/1.10 supp.440V

ZZ0045020

01440

10

25

150

AMS90/1.20 supp.230V

ZZ0045020

02230

AMS90/1.20 supp.400V

ZZ0045020

02400

AMS90/1.20 supp.415V

ZZ0045020

02410

AMS90/1.20 supp.440V

ZZ0045020

02440

20

25

150

AMS90/1.30 supp.230V

ZZ0045030

03230

AMS90/1.30 supp.400V

ZZ0045030

03400

AMS90/1.30 supp.415V

ZZ0045030

03410

AMS90/1.30 supp.440V

ZZ0045030

03440

30

1,5

32..35

250

WARNING:

 The use of extra-quick fuses FU1/2 is recommended to protect the internal

power module in case of undesired external short-circuits. Comply with the max.
prescribed value for I

2

t.

The L1 switching impedance is 35A/150

µ

H

(ELETTRONICA SANTERNO code:  IM0100354).

The current FF form factor can be obtained by measuring the effective value 

[ ]

a

e

I

 of the

alternate component of the current absorbed by the motor (with a A.C. instrument with
real effective value) and the mean value 

I

m

 

of the same current (with a D.C. instrument).

The result is given by the following formula:

[ ]

m

m

a

e

I

I

I

FF

2

2

+

=

Since the motor and drive heating, as well as the periodical maintenance operations on
brushes and manifold, depend on the form factor, apply the levelling inductance L2 so
as to keep the form factor value as close as possible to 1.

Through the following formula, you can get the L2 mH value of the levelling inductance
to be inserted, assuming the motor one is negligible, using the desired form factor FF
value, the supply alternate voltage 

V

a  

value and the mean output current 

I

m

 value:

[ ]

1

9

.

0

2

2

=

FF

I

V

mH

L

m

a

Summary of Contents for AMS90/1 Series





















Reviews: