background image

15P0056B1

APPLICATION MANUAL     

AMS90/1

  

2/17

TABLE OF CONTENTS

TABLE OF CONTENTS

Standard configuration.............................................................................. Page

2

General features .......................................................................................

"

3

External and fixing dimensions (fig. 1)  .....................................................

"

4

Power and supply connections  ................................................................

"

5

Signal connections ...................................................................................

"

5

Power and supply connections diagram (fig. 2)  .......................................

"

6

Signal connection diagram (fig. 3) ............................................................

"

7

Size codes and extra-quick fuses table ....................................................

"

8

ES719 control board description ...............................................................

"

9

Adjustment trimmers............................................................................

"

9

Signalling LED’s...................................................................................

"

9

Preset jumpers.....................................................................................

"

10

Selection dip-switches .........................................................................

"

10

ES719 control board layout (fig.  4) ..........................................................

"

11

Terminal board description .......................................................................

"

12

Technical data table..................................................................................

"

13

EMI characteristics and input filter  ...........................................................

"

14

Installation, calibration and maintenance  .................................................

"

15

                               

IMPORTANT NOTICE

If, after powering the unit, closing the run contact and sending the speed reference, the motor does
not start, check that the power circuit supply at term. 23-24 has the SAME PHASE of the control
circuit supply at term. 25-26.
If in doubt, with power circuit on (remote control switch closed, if any), check that an alternate
voltage is present with a zero effective value (

±±

 200mV) between terminals 23 and 25, and between

terminals 24 and 26.

STANDARD CONFIGURATION

STANDARD CONFIGURATION

If no custom configuration is required, the standard configuration of the AMS90/1 drive
is the following:

SUPPLY VOLTAGE:

  400Vac / 50Hz.

TACHO GENERATOR FEEDBACK:

  180V

DC

 max.

CURRENT LIMIT:

 rated value.

WARNING

WARNING

:

 before powering the unit on

, check that the voltage (

TR3

J2

) and

frequency (

SW1

) values on the plate match those of the supply mains at terminals 25-

26.

Summary of Contents for AMS90/1 Series





















Reviews: