background image

 This manual is integrant and essential to the product. Carefully read the instructions contained herein

as they provide important hints for use and maintenance safety.

 This device is to be used only for the purposes it has been designed to. Other uses should be

considered improper and dangerous. The manufacturer is not responsible for possible damages
caused by improper, erroneous and irrational uses.

  Elettronica Santerno is responsible for the device in its original setting.

 Any changes to the structure or operating cycle of the device must be performed or authorized by the

Engineering Department of Elettronica Santerno.

 Elettronica Santerno assumes no responsibility for the consequences resulting by the use of non

original spare-parts.

 Elettronica Santerno reserves the right to make any technical changes to this manual and to the

device without prior notice. If printing errors or similar are detected, the corrections will be included in
the new releases of the manual.

 Elettronica Santerno is responsible for the information contained in the original version of the Italian

manual.

 The information contained herein is the property of Elettronica Santerno and cannot be reproduced.

Elettronica Santerno enforces its rights on the drawings and catalogues according to the law.

Elettronica Santerno S.p.A.

Via G. Di Vittorio, 3 - 40020 Casalfiumanese (BO) Italy

Tel. +39 0542 668611  -  Fax +39 0542 666632

After Sales Service  Tel. +39 0542 668610  -  Fax +39 0542 666778

Sales Office  Tel. +39 051 6010231  -  Fax +39 051 534403

Summary of Contents for AMS90/1 Series





















Reviews: