Disposal
Batteries and old units may not be
disposed of with household waste.
1.
Dispose of packaging in the recy
-
cling bin for cardboard and paper.
2.
Dispose of old batteries in the
recycling bin for used batteries
or have a retailer recycle them.
3.
Dispose of old units at an elec
-
tronic waste recycling facility or
have a retailer recycle them.
Conformity
elero
hereby declares that Mono
-
Tec-915 wall transmitter is in com
-
pliance with Directive 2014/53/EU.
The full text of the EU Declaration
of Conformity is available at the
following Internet address:
www.elero.de/downloads-service/
Service /
manufacturer's address
If malfunctions have occurred or the
device has been damaged despite
proper handling, contact your con
-
tractor or dealer.
elero
GmbH
73278 Schlierbach
GERMANY
www.elero.de
Notes on troubleshooting
Fault
Cause
Remedy
Drive not
running,
indicator
light not
illuminating
Battery
depleted
The bat
-
tery is
incorrectly
installed
Install
a new
battery
Install the
battery
correctly
Drive not
running,
status
LED dis-
play flash
-
ing red
1.
The
receiver
is outsi-
de radio
range.
2. Recei-
ver not
opera
-
ting or
faulty
3. Recei-
ver not
yet pro
-
gram
-
med
1. Reduce
distance
to the
receiver
2.
Switch
on or
replace
receiver
3. Pro-
gram
receiver
Drive
runs in
the wrong
direction
Directions
are incor-
rectly pro
-
grammed
Delete
transmit-
ter and
program
correctly
Repair
Please specify the item number,
item description, type of fault, situ
-
ational circumstances, presumed
cause, unusual events prior to the
problem.
Cleaning
Clean the device with a damp cloth
only. Do not use cleaning agents be
-
cause they can damage the plastic.
Warranty
Within the legal warranty period, we
will remedy any defects caused by
material or manufacturing defects
by repairing or replacing the unit.
Unauthorised modifications will void
the warranty.
Status LEDs and their
meanings
Orange
flashing
slowly
Channel (trans
-
mitter) not pro
-
grammed in any
receiver
Orange
flashing
quickly
Channel (transmit
-
ter) is in program
-
ming mode. Opera
-
tion of already pro
-
grammed receivers
is not possible.
Orange flash
-
ing quickly
(approx.
every
2 seconds)
More than
10 receivers
are ready for
programming.
Orange lights
up, then
green
Transmit signal is
being sent, all re
-
sponse messages
received
Orange or
green flashes
several times,
then red after
6 seconds
Channel (trans
-
mitter) has been
deleted
Orange lights
up, then red
Transmit signal is
being sent, not all
response messages
received
Red flashing
quickly
Battery almost
depleted
Synchronised programming
mode
For programming one transmitter to
multiple receivers at the same time.
1.
Press the
DOWN/CLOSE
buttons
and the programming button
P
simultaneously for 3 s on a trans
-
mitter that has already been pro
-
grammed to the receiver. The sta
-
tus LED flashes orange and green
multiple times. The receivers are
now in programming mode.
2.
Perform steps 2 to 7 under “Pro
-
gramming the transmitter / channel”
with the transmitter to be pro
-
grammed.
Configuring the drive
Programming the intermediate position
Requirement:
The blind is in the upper end position.
1.
Press the
DOWN/CLOSE
button until the
desired intermediate position is reached.
2.
Additionally press the
STOP
button.
The blind will stop. The intermediate
position has now been stored.
Programming the ventilation / tilting /
fabric tautening positions
Requirement:
The blind is in the lower end position.
1.
Press the
UP
button until the louvres
open, the venetian blind slats are tilted
or the awning fabric is taut.
2.
Additionally press the
STOP
button.
The blind will stop. The ventilation / tilting /
fabric tautening position has been stored.
Moving to the intermediate position
Requirement:
The intermediate position has been
programmed.
1.
Press the
DOWN/CLOSE
button twice
quickly. The blind will move to the stored
intermediate position.
If no intermediate position has been pro
-
grammed, the blind will move to the lower
end position.
Important: If you are using venetian blinds
and a programmed tilt position, the venetian
blind slats will also tilt.
If no tilt position has been preprogrammed,
the blind will stop at the intermediate position
with closed slats.
Moving to the ventilation / tilting / fabric
tautening positions
Requirement:
The ventilation / tilting / fabric tautening
position has been programmed.
1.
Press the
UP
button twice quickly.
The blind will move to the stored position.
If no ventilation / tilting / fabric tautening
position has been programmed, the blind will
travel to the upper end position.
You can also use a programmed hand-held
transmitter to travel to the ventilation / tilting /
fabric tautening position.
Deleting the intermediate position
Requirement: The transmitter is pro
-
grammed.
1.
Press and hold down the
DOWN/CLOSE
button and the
STOP
button simultaneous-
ly for approximately 3 s.
The intermediate position is now deleted.
The indicator light will light up briefly.
Deleting the ventilation position / tilting
position / fabric tautening position
Requirement: The transmitter is programmed.
1.
Press and hold down the
UP
button and
the
STOP
button simultaneously for
approximately.
The ventilation / tilting / fabric tautening
position has now been deleted.