background image

Delete individual transmitters 

Press the teach-in button 

P

 (on the rear side of the device) and the 

STOP

- button (on the front of the device) 

simultaneously

Continue to hold this combination of keys until the LED extinguish-
es briefly a second time (approx. 6 seconds). 

Delete all transmitters  

Press the teach-in button 

P

 (on the rear side of the device) and the 

UP

DOWN

 and 

STOP

 buttons (on the front of the device) simul-

taneously. 

Continue to hold this combination of keys until the LED extinguish-
es briefly a second time (approx. 6 seconds). 

24 | EN 

Program transmitter / program end positions
AstroTec-868 bidi/-915 bidi 

Programming/deletion of the radio transmitter

As long as the AstroTec-868 bidi/-915 bidi has not been programmed for 
at least one receiver, each press of a button results in an acoustic signal 
being issued to inform you that programming must yet take place.

Programming the transmitter

Condition: the drive must be installed

1. 

With electrical, previously installed bidirectional receivers, turn the 
safety fuse off and after a few seconds on again. The actuator is 
now in programming mode for a period of approximately 5 minutes.

2. 

Position yourself in front of the roller shutter with the AstroTec-868 
in your hand.

3. 

Press the programming button P on the back of the device briefly.
The shutter will automatically begin to move up and down for 
approx. 2 minutes.

4. 

In order to define the keyboard layout, press the UP button (front of 
the device) on the AstroTec-868 bidi/AstroTec-915 bidi immediately 
(max. 1 second) after beginning upward motion; the status of the 
bidirectional programming is acoustically signalised.

The roller shutter stops briefly and then continues to travel again.
Press the DOWN button on the AstroTec-868 bidi/-915 bidi imme-
diately after beginning downward travel; the status of bidirectional 
programming is acoustically signalised.The roller shutter stops.

The AstroTec-868 bidi /-915 bidi is now programmed.

EN | 25

AstroTec-868 bidi/-915 bidi 

Summary of Contents for AstroTec-868 bidi


























Reviews: