2
Function for "Auto" switch setting (manual transmitter)
The
UP-STOP-DOWN
button on the manual transmitter and the
UP/DOWN
keys at the Aero-915 are active.
– Wind monitoring is active
– Sun protection is active.
Semi-automatic mode
Your Aero-915/Aero-915 Plus is in AUTO mode.
As soon as you now press a button on your programmed manual
transmitter the receiver switches itself into the semi-automatic
mode.
Leave semi-automatic mode:
– If a level falls below and/or rises above a set threshold value then
the system automatically changes to AUTO mode.
The system moves in/out.
or
– Set the sliding switch of your transmitter briefly to
MANUAL mode and then to AUTO mode.
The system moves in.
Loading the Aero-915/Aero-915 Plus
The Aero-915 is supplied in discharged condition.
1. Prior to commissioning, load the Aero-915 for at least minimum 30
minutes under a lamp or press a travel key for at least 1 minute.
Advice:
the travel keys have two settings.
The first setting transfers energy from a built-in cell to the energy
store.
The second setting activates the travel command.
Programming the Aero-915/Aero-915 Plus
Condition: The end positions of the awing are set, a transmitter is
programmed.
Start teach mode
1.
Blind/shutter
runs up and
down for
2 minutes.
min. 3 sec.
elero
2.
3.
STOP
STOP
Press the ”
UP
”
(wind symbol)
button
imme-
diately
after the
start of upward
travel .
Press the ”
DOWN
”
(sun symbol)
button
immedia-
tely
after the start
of downward
travel.
"Teach-in" programmed
transmitter.
10
12
14
2
Off
8
4
6
11
1
3
9
5
7
10
12
14
2
Off
8
4
6
11
1
3
9
5
7
Setting the threshold values
Multiple contact switches for wind and sun are located at the
underside of the Aero-915. The switch has several settings, which
can be modified with a small screwdriver..
Wind
Setting 1
➯
Retract at low wind speed
Setting 2 bis 10
➯
Intermediate levels
Setting 4
➯
Factory setting
Setting 11
➯
Retract at high wind speeds
Sun
Setting OFF
➯
Light function is deactivated
Setting 1
➯
Move out at low light levels
Setting 2 bis 13
➯
Intermediate levels
Setting 4
➯
Factory setting
Setting 14
➯
Move out in full sun
11
1
3
9
5
7
10
12
14
2
Off
8
4
6
red LED
yellow LED
Function for "Manual" switch setting (manual transmitter)
The
UP-STOP-DOWN
button on the manual transmitter and the
UP/DOWN
keys at the Aero-915 are active.
– Wind monitoring is active
– Sun protection is disabled.
Device function
Light intensity and wind speed are measured at regular intervals
and compared with the set values.
Brightness above set value
➩
Awning moves out after delay time
(Delay time approx. 5 min.)
(yellow LED winks).
Brightness below set value
➩
Awning retracts after delay time or
(Delay time approx. 15 min.)
remains retracted .
Wind value above set value
➩
Awning retracts or remains retracted
and is blocked for around 15 min.
(red LED flashes)
The slide switch at the taught manual transmitter can be used to
switch the light function of the Aero-915 AC on or off. The wind
function is always active, irrespective of the light switch setting.
The slide switch has no influence on the function of the travel keys.
However, in the event of a wind alarm, the keys are disabled for
15 minutes.