background image

Figure F

Lytics have a polarity marking on
them indicating the negative lead, the
opposite lead is positive.

The PC

board is marked to show the positive
(+) lead position. Mount the capacitor
with the positive (+) lead in the hole
marked on the PC board. Bend the
capacitor over.

R6 - 100

.5% 1/4W Res.

(brown-blk-blk-blk-green)

(see Figure E)

R5 - 900

.5% 1/4W Res.

(white-blk-blk-blk-green)

(see Figure E)

R4 - 9k

.5% 1/4W Res.

(white-blk-blk-brown-green)

(see Figure E)

R3 - 90k

1/4W .5% Res.

(white-blk-blk-red-green)

(see Figure E)

R2 - 900k

.5% 1/4W Res.

(white-blk-blk-orange-green)

(see Figure E)

R1 - 9M

.5% 1/2W Res.

(white-blk-blk-yellow-green)

(see Figure B)

D1 - 1N4001 Diode
D2 - 1N4001 Diode

(see Figure C)

R12 - 9

1/4W .5% Res.

(white-blk-blk-silver-green)

(see Figure B)

R13 - 1

.5% 1/2W Res.

(brown-black-gold-green)

(see Figure B)

Fuse Holder Clips
Fuse 2A

Mount holders with the tab
side as shown on the top
legend then insert fuse.

-14-

ASSEMBLE THE  FOLLOWING  COMPONENTS TO THE  PC  BOARD

In all of the following steps 

the components must be installed on the top legend side of the PC board. The

board is turned to solder the component leads on the selector switch side

.

Figure E

Stand resistor on end as
shown with the body
inside the white circle.

White
Circle

R26 - 8.2k

5% 1/4W Res.

(gray-red-red-gold)

(see Figure E)

R25 - 39.2k

1% 1/4W Res.

(orange-white-red-red-brown)

(see Figure E)

C1 - 22

µ

F Lytic Capacitor

(see Figure F)

R27 - 2k

1% 1/4W Res.

(red-blk-blk-brown-brown)

(see Figure E)

R28 - 1.3k

1% 1/4W Res.

(brn-orange-blk-brn-brn)

(see Figure E)

R46 - 5.6k

5% 1/4W Res.

(green-blue-red-gold)

(see Figure E)

VR1 - 200

Potentiometer

Shunt

+

C1

+

Tab

Push into board

up to stops

Solder the spring to the PC board as shown in
Figure Ja.

See Figure K for the following steps.

Peel off the protective backing on the top plates
(A) and (B) and stick them to the top case. Peel
off the protective backing on the battery cushion
and stick it onto the bottom case.

(These may be

installed on the case already)

.

Turn the selector knob screw one full turn out as
shown in the figure.

Place the PC board on a standard piece of paper
(8 1/2” x 11”). Insert the two springs into the
holes on the range selector knob. Put grease on

top of the springs and then place a ball bearing
on each spring. Press the top case onto the PC
board.

Using both hands, slide your fingers

under the paper. Press your thumbs down on the
top case and then flip the board. Be sure to hold
the PC board to the case firmly or the ball
bearings will fall out. Fasten the PC board to the
top case with three M2.3 x 6 screws in the places
shown in Figure J.

Connect the battery and place it in the cavity of
the top case.

Place the bottom case onto the top case. Hold
the two sections together with two M3 x 12
screws.

-21-

FINAL ASSEMBLY

Spring

Pad

Screw Holes

Figure J

Figure Ja

Solder

Spring

Summary of Contents for M-2665K



















Reviews: