background image

-2-

PARTS IDENTIFICATION

Switch 12 Position

9mm Nut

Alligator Clip

Switch PC Mount

Capacitor

Washer

PC Board

IDENTIFYING CAPACITOR VALUES

Capacitors will be identified by their capacitance value in pF (picofarads), nF (nanofarads), or 

μ

F (microfarads).  Most

capacitors will have their actual value printed on them.  Some capacitors may have their value printed in the following
manner.  The maximum operating voltage may also be printed on the capacitor.

Second Digit

First Digit

Multiplier

Tolerance

The letter M indicates a
tolerance of +20%

The letter K indicates a
tolerance of +10%

The letter J indicates a
tolerance of +5%

For  the  No.

0

1

2

3

4

5

8

9

Multiply By

1

10

100

1k

10k 100k .01

0.1

Multiplier

Note:  The letter “R” may
be used at times to
signify a decimal point;
as in 3R3 = 3.3

103K

100V

Maximum
Working Voltage

The value is 10 x 1,000 = 10,000pF or .01

μ

F  100V

10

μ

F 16V

METRIC UNITS AND CONVERSIONS

Abbreviation

Means

Multiply Unit By

Or

p

Pico

.000000000001

10

-12

n

nano

.000000001

10

-9

μ

micro

.000001

10

-6

m

milli

.001

10

-3

unit

1

10

0

k

kilo

1,000

10

3

M

mega

1,000,000

10

6

1. 1,000 pico units = 1 nano unit

2. 1,000 nano units = 1 micro unit

3. 1,000 micro units= 1 milli unit

4. 1,000 milli units = 1 unit

5. 1,000 units

= 1 kilo unit

6. 1,000 kilo units = 1 mega unit

Electrolytic capacitors have a positive
and a negative electrode. The negative
lead is indicated on the packaging by a
stripe with minus signs and possibly
arrowheads.

Warning:

If the capacitor is
connected with
incorrect polarity, it
may heat up and
either leak, or
cause the capacitor
to explode.

Polarity
Marking

Summary of Contents for K-38









Reviews: