background image

14 / 20

CARE AND CLEANING

Inspecting

This outdoor fire table must be inspected regularly to insure that the product is safe to use and to 

extend product life.

WARNING

!

1. Check the burner to make sure it is securely in place.
2. Check all gas connections for leaks.
3. Check ignition system to insure proper sparking.
4. Check components for any signs of damage, rust or excessive wear.
5. If damage to any component is detected, DO NOT operate until the proper repairs have been made.

WARNING 

!

DO NOT tamper with this appliance. This is DANGEROUS and will void the

warranty. Any part found to be faulty must be replaced with an approved part, 

confirmed by manufacturer. For technical support contact Elementi at 

800-678-7294 .

WARNING

!

DO NOT inspect this outdoor fireplace until the fire is 

COMPLETELY out.

DO NOT move or store this fire table unless the fire is COMPLETELY out and

cool to the touch.

General Care and Cleaning

This outdoor fireplace should be cleaned regularly to ensure safe use and extend product life.

Note: After repeated use, a slight discoloration of the finishes may occur.

Table

1. Wipe exterior surfaces with a mild dish washing soap or baking soda, then rinse clean with water.

Stainless Steel

1. For general cleaning use warm water, soap, ammonia, or detergent apply with a soft cloth or Sponge

2. For finger prints or smears use 3M Stainless Steel Cleaner and Polish, Arcal 20, Lac-O-Nu, LuminWash, 

O’Cedar Cream Polish, or Stainless Shine, this will provide a barrier file to minimize fingerprints.

3. For stubborn stains and discoloration use 3M Stainless Steel Cleaner and Polish, Allchem Concentrated 

Cleaner, Samae, Twinkle, Cameo Copper Cleaner, Liquid Nu Steel, Copper’s or Revere Stainless Steel 

Cleaner, apply using a soft cloth in the same direction of the polish lines.

4. While using in salt air environments we recommend cleaning all stainless steel surfaces at least every two 

weeks to keep the item in prime condition. Stainless steel is corrosion-resistant but it is not impervious to rust. 

Exposure to salt air and sea spray will cause surface rust if you do not care for your products properly. 

The best thing you can do to protect the stainless steel is to clean it frequently.

* Use of proprietary names is intended only to indicate a type of cleaner and does not constitute endorsement. Omission 

of any proprietary cleanser does not imply its inadequacy. All products should be used in strict accordance with 

instructions on package.

Storage

1. Turn gas OFF at tank connection. Remove tank and store in a cool, dry location outdoors, away  from 
children.
2. Carefully remove rock filler and store components flat to protect them from breakage.
3. ALWAYS cover your outdoor fire table when not in use with the cover provided with the unit.
4. Store in a cool, dry location away from children and pets.

Summary of Contents for OFS006NG





















Reviews: