background image

 

1. Unit

 

The lightweight tiller is together with a high-efficient 4 strike engine. This design is ideal for tilling 

close-planted  crops  with  semi-hard  soils.  When  in  operation,  it  runs  steady  and  is  quite  silent. 

The  tiller  is  made  of  a  little  special  wearable  steel  so  it  provides  for  good  cost-effectiveness.  A 

special shape of blades provides for thrifty and efficient tilling. The turning guide wheel keeps the 

tiller  operation  easily.  Start-up  system  responding  to  a  button  pressing  (the  tiller  will  run  upon 

pressing an operation button in rest (state) improves the labor safety. 

 

Scope of delivery

 

 

 

1.

 

carriage 

2.

 

left-hand handle(driving lever) 

3.

 

depth limiter 

4.

 

bracket and handle 

5.

 

wheel 

6.

 

right-hand handle (on/off, speed) 

7.

 

right-hand blade 

8.

 

left-hand blade 

9.

 

Left-hand Blade protector 

10.

 

Right mudguard 

11.

 

Left mudguard   

12.right-hand Blade protector 

 

 

 

2. General safety instructions

 

Prior to the initial use of the unit, the operating instructions should be read completely. If in 

doubt with regard to connection and operation of the unit, consult the manufacturer (servicing 

department).This machine shall always be used in this instructions laid down in the instruction 

handbook. 

info@eco-repa.com

    / 

www.eco-repa.com

 

 

FOLLOW  THE  INSTRUCTIONS  BELOW  CAREFULLY  IN  ORDER  TO  SECURE  A  HIGH  DEGREE  OF 

SAFETY: 

CAUTION! 

1.

 

Pay  attention  to the  conditions  of  the  area

,

  which  you  are  working  in.

  after  the  engine  is 

started;  power  machine  will  produce  poisonous  flue  gas.  The  gas  may  be  invisible  and 

odorless. Hence never work with the machine closed or poorly ventilated areas. Provide for 

good  lighting  when  cutting.  Provide  for  stability  when  cutting  in  wet,  snow  or  icy  weather 

conditions on slopes or rough ground. 

2.

 

Do  not  let  any  unauthorized  person  approach  the  machine.

  The  visitors  and  viewers 

primarily the children, the ill and infirm persons should not have any access to the working 

Summary of Contents for MTBT59-CC139L





















Reviews: