background image

 

 

 

Flg.8

 

Refueling 

Use only regular leadless petrol 

Explosion hazard! 

Refuel outdoors only! 

Never  refuel  with  engine  running  or  while  it  is 

still hot! 

Do not smoke and do rot handle open fire. 

Engine oil filling 

Use only oil type 15W40! 

Use oil dip rod to check the filling status. 

 

Avoid  fuel  or  oil  splashing  so  that  soil 

contamination  is avoided. Use appropriate tools 

for filling(funnel)

 

 

5.1 safety instructions for the first putting in operation 

Always make sure that the screwed parts are tight as appropriate and use only the parts 

included in the delivery. 

 

5.2 procedure 

    Assemble  separate  parts  in  the  correct  order  as  shown.  Make  sure  that  structural  parts 

are arranged as shown in figures. 

the unit is delivered without oil and fuel. Fill in the liquids according to specifications.

 

 

6. OPERATION 

 

Guiding wheel in work position 

Put the wheel in pos. 1 for working. 

CAUTION! 

Transport the unit with the wheel in pos.2 

The wheel can be adjusted with engine off 

only! 

 

Cutting height setting 

Shifting the depth limiter shall set up the 

required depth of tilling. 5 different 

positions are possible. 

Summary of Contents for MTBT59-CC139L





















Reviews: