Elektro-Automatik EA-PS 10000 3U, Manual

Page: 2 / 72

© EA Elektro-Automatik in 2022, this information is subject to change without notice 2 06230920_manual_ps_10000_3u_15kw_en_01
TABLE OF CONTENTS
1. General
1.1 About this document 4
1.1.1 Retention and use 4
1.1.2 Copyright 4
1.1.3 Validity 4
1.1.4 Symbols and warnings 4
1.2 Warranty 4
1.3 Limitation of liability 4
1.4 Disposal of equipment 5
1.5 Product key 5
1.6 Intended usage 6
1.6.1 Symbols and warnings on the device 6
1.7 Safety 7
1.7.1 Safety notices 7
1.7.2 Responsibility of the operator 8
1.7.3 Requirements to the user 8
1.7.4 Responsibility of the user 8
1.7.5 Alarm signals 9
1.7.6 Functionality test 9
1.8 Technical data 10
1.8.1 Approved operating conditions 10
1.8.2 General technical data 10
1.8.3 Specific technical data 11
1.8.4 Views 16
1.8.5 Control elements 19
1.9 Construction and function 20
1.9.1 General description 20
1.9.2 Block diagram 20
1.9.3 Scope of delivery 21
1.9.4 Accessories 21
1.9.5 Options 21
1.9.6 The control panel (HMI) 22
1.9.7 USB port (rear side) 24
1.9.8 Interface module slot 25
1.9.9 Analog interface 25
1.9.10 “Share BUS” connector 25
1.9.11 “Sense” connector (remote sensing) 26
1.9.12 Master-Slave bus 26
1.9.13 Ethernet port 26
2. Installation & commissioning
2.1 Transport and storage 27
2.1.1 Transport 27
2.1.2 Packaging 27
2.1.3 Storage 27
2.2 Unpacking and visual check 27
2.3 Installation 27
2.3.1 Safety procedures before installation and use 27
2.3.2 Preparation 27
2.3.3 Installing the device 28
2.3.4 Connection to AC supply 29
2.3.5 Connection to DC loads 32
2.3.6 Connection of remote sense 34
2.3.7 Grounding of the DC output 35
2.3.8 Installation of an interface module 35
2.3.9 Connecting the analog interface 36
2.3.10 Connecting the Share bus 36
2.3.11 Connecting the USB port (rear side) 36
2.3.12 Initial commission 36
2.3.13 Commission after a firmware update or a long
period of non-use 36
3. Operation and application
3.1 Personal safety 37
3.2 Operating modes 37
3.2.1 Voltage regulation / Constant voltage 37
3.2.2 Current regulation / constant current / current
limiting 38
3.2.3 Power regulation / constant power / power
limiting 38
3.2.4 Internal resistance regulation 38
3.3 Alarm conditions 39
3.3.1 Power Fail 39
3.3.2 Overtemperature 39
3.3.3 Overvoltage protection 39
3.3.4 Overcurrent protection 39
3.3.5 Overpower protection 39
3.3.6 Safety OVP 40
3.3.7 Share bus fail 40
3.4 Manual operation 41
3.4.1 Switching on the device 41
3.4.2 Switching the device off 41
3.4.3 Configuration via the menu 41
3.4.4 Adjustment limits 49
3.4.5 Changing the operating mode 49
3.4.6 Manual adjustment of set values 50
3.4.7 Switching the DC output on or off 51
3.4.8 Recording to USB stick (logging) 51
3.4.9 The quick menu 52
3.4.10 The graph 53
3.5 Remote control 54
3.5.1 General 54
3.5.2 Control locations 54
3.5.3 Remote control via a digital interface 54
3.5.4 Remote control via the analog interface 56
3.6 Device alarm handling 60
3.7 Locking the control panel (HMI) 62