manualshive.com logo in svg

Electronics Line Penta, Installation Manual

Share
Download
Electronics Line Penta Installation Manual Download Page 27

-27-

Primary

Telephone Number

The first telephone number dialed when an event occurs. If
communication can not be established with the Primary telephone the the
Backup telephone number is dialed.

Q

Quick Arming

Arming the system without the need for a valid user code.

R

Ready

The state in which all zones are closed and the system is ready to be
armed.

Remote

Programmer

The software developed by Electronics Line used for programming the
system using a PC from a remote location or on-site.

Restore

The restoral of a trouble condition to its normal state. For example, if AC
power is reconnected, an AC Loss Restore event code is sent to the
central station.

RP

Abbreviation of Remote Programmer

RP Access Code

The code that grants access to the remote programmer. The RP Access
Code prevents the system being sabotaged using unauthorized remote
programming.

S

Silent Alarm

An alarm that does not activate the bell/siren when generated.

Stay Arming

Arming the perimeter of the system while allowing free movement in the
interior zones.

Stop

Communications

An operation that clears all communication buffers and stops all
communications immediately.

T

Tamper Zone

The fifth zone which can be connected to a tamper switch protecting the
control panel by generating an alarm when the metal housing is opened.
Alternately, the tamper zone can be defined for use with an On/Off
keyswitch.

Tone

See Beep

U

Unbypass

The restoral of a bypassed zone to its original state.

User Code

A code that grants access to certain operational capabilities such as
arming and disarming the system.

V

Voice Message

A short message played by the 3601 module to announce an alarm over
the telephone line.

W

Walk Test

A mode that enables detection devices to be tested without generating an
alarm.

Z

Zone

The physical and logical connection of detection devices to the control
panel.

Zone Chime

The tone sounded by a keypad on opening a perimeter zone when the
system is disarmed.

Summary of Contents for Penta


































Reviews:

No comments

Brands by name

Popular brands

Load more brands