manualshive.com logo in svg

Electronics inc 250-N, Instruction Manual

Share
Download
Electronics inc 250-N Instruction Manual Download Page 6

6  

 

sired value then adjust the Model FC Front panel span adjustment until it does. 

I.  A catch test can be run to verify the accuracy of the maximum flow rate of the Magna-

Valve. If necessary, Adjust the Pre-Amp span adjustment ( not the FC controller span 
adjustment) and repeat the catch and weigh tests until the correct amount of shot is 
caught. Adjust the span once at any desired flow rate for proper flow then fill in the 
chart to check performance.  

J.  Confirm the accuracy by filling in the table column marked “Actual lbs/min” in the table 

corresponding to the desired maximum flow rate. Correct discrepancies by making ad-
justments to the compensation trimpots as necessary. 
The Tables are located at the end of this document. 
 

4.  Trouble shooting  

 
For additional troubleshooting information see the model FC installation manual IM0056.  

 

For assistance call or fax the factory for help 

 

Phone 1-(574)-256-5001 

 

FAX 1-(574)-256-5222 

 

www.shotpeener.com 

 

 

Summary of Contents for 250-N









Reviews:

No comments

Brands by name

Popular brands

Load more brands