ELECTROMATIC WTT-110 User Manual Download Page 10 | Manualshive

Page: 10 / 11

ELECTROMATIC WTT-110 User Manual Download Page 10

– 10 –

10.0 A

DJUSTING

A

DVANCED

S

ETTINGS

There are several adjustable settings that can be changed from the factory defaults to
customize the WTT-110 to meet the exact requirements of the user. These settings are
saved in the microprocessor and are recalled each time the system is powered up.

10.1 Temperature Compensation (Default: SET=on)

In general, it is recommended to have the this function turned on as long as it
does not effect your measuring results. Only when measuring very minute
forces over a longer period of time at a slow rate and under stable environmental
conditions might it be useful to switch this off.

■

Switch off the instrument.

■

Press and hold PEAK- and MODE-buttons.

■

Press ON/OFF-button.

■

Wait until TRK oFF is displayed.

■

Release PEAK- and MODE-buttons.

10.2 Selecting the baud rate of the RS232C interface (Default: 2400)

On the WT-110RS model ONLY, the speed of the data transfer for the RS232C
interface can be adjusted as follows:

■

Switch off the instrument.

■

Press and hold RESET-button.

■

Press ON/OFF-button.

■

Wait until f01 is displayed, then release RESET-button.

■

Select function f04 by repeating to press the PEAK-button until f04 is shown
on the display.

■

Select appropriate baud rate (2400/4800/9600/19200) by repeating to press
the MODE-button.

■

Press RESET-button to save your settings.

10.3 Switching off Auto Power-Off function (Default: 10 min)

While operating under battery power the instrument will be automatically
switched off after approx. 10 minutes on inactivity. This Auto Power-Off func-
tion can be deactivated, which may become necessary when monitoring the
fluctuation of applied forces for a longer period of time. This function is
disabled when the instrument is powered by the AC-adaptor.

■

Switch off the instrument.

■

Press and hold RESET-button.

■

Press ON/OFF-button.

■

Wait until f01 is displayed, then release RESET-button.

■

Select function f03 by repeating to press the PEAK-button until f03 is shown
on the display.

■

Select setting (10/OFF) by repeating to press the MODE-button.

■

Press RESET-button to save your settings.

TRK

oFF

– 11 –

10.4 Change the refresh rate of the display (Default: 3/sec)

The force applied to the load cell of the instrument is internally processed at a
rate of 1000 Hz, which allows the precise capturing of the peak values. The read-
ings on the display, however, are refreshed 3 times/sec only for the convenience
of the human eyes. You may increase or decrease the factory settings for them to
match your personal demands.

■

Switch off the instrument.

■

Press and hold RESET-button.

■

Press ON/OFF-button.

■

Wait until f01 is displayed, then release RESET-button.

■

Select function f02 by repeating to press the PEAK-button until f02 is shown
on the display.

■

Select refresh-time (1/2/3/5/10/20 times/sec) by repeating to press the
MODE-button.

■

Press RESET-button to save your settings.

«
...
8
9
10
11
»

Summary of Contents for WTT-110












Reviews:

No comments