MODELS: SB915SJ*05
SB915WJ*05
CONTROL PANEL LAYOUT
SB925SJ*05
SB925WJ*05
(cont.)
Child Lock Off
To turn Child Lock off you must be in Program Selection mode
Firstly “Temporarily unlock” Child Lock as shown above.
Press & hold “LOCK” for 5 seconds
All Program Indicators will flash.
“LOCK” Indicator also will flash.
The Child Lock is now permanently off.
“LOCK” indicator turns off
Unit is in Program Selection mode
Other Helpful Hints
You must use sufficient rinse aid to get good drying performance. This is especially important with plastic dishes. Even when using ‘3-in-1’
/ Combi detergent tablets, you may need to use a small amount of rinse aid as well, particularly in hard water areas. Refer to Section C in the
Care and Use Manual for more details on Rinse Aid use and dosage adjustment.
Because this dishwasher has a hidden heating element, dishwasher proof plastic dishes can be safely placed in the bottom basket.
The Door Handle enables the door to open easily but, as a safety feature, it is possible to open the door without using the handle.
The initial wash time shown in the digital display window (915 & 925 models) may vary over time. The dishwasher adjusts the displayed
wash time after each wash depending on the wash load and water conditions detected.
The
NORMAL ECO
program saves energy and water. It runs at a lower temperature but for a longer time to ensure the wash performance.
To save energy, dry performance is reduced so you may have to open the door at the end of the wash cycle or even towel dry some dishes.
The Child Lock disables the button functions to prevent children from starting or disrupting a dishwasher in use.
It does not lock the door
.
See the following instructions for a full description of Child Lock operation.
Boosted Dry Option (SB907, SB915 and SB925) (Customer Option)
To gain enhanced drying performance by boosting the temperature and time during the final rinse, use this procedure:
Select Normal or Normal-Eco wash program.
Press
PROGRAM
and
START
buttons
simultaneously
. The estimated wash time shown on the display will increase by around 10 – 20
minutes indicating that the Boost Dry Option is on.
On Model 907 the “Dry” progress indicator will come on for 3 seconds.
Press
START
to begin wash program.
To turn off Boosted Dry, repeat the above procedure.
Boosted Dry remains on for subsequent cycles until turned off.
The Boosted Dry option does not apply to the Rinse or Fragile wash programs.
Fault Recall and Output Test (SB915)
O
PERATION
I
TEM
I
NPUT
O
UTPUT
Enter Test Mode
Switch dishwasher off by pressing the ‘POWER’
Button
All off
Press & hold ‘PROGRAM’ Button &
‘START/PAUSE’ Button then switch power on.
Keep holding the 2 Button for 2 sec.
‘RINSE’ LED flashing Display show '1C'
Select F/O Test
Press ‘PROGRAM’ Button
‘FRAGILE’ LED flashing Display shows '2C'
Enter F/O Test
Press ‘START/PAUSE’ Button
‘FRAGILE’ LED on. Display & buzzer showing the last occurred fault (see
‘Fault Indication’ table Page 20)
Press ‘PROGRAM’ Button
Display & buzzer showing the 2
nd
last occurred fault
Press ‘PROGRAM’ Button
Display & buzzer showing the 3
rd
last occurred fault
Press ‘PROGRAM’ Button
‘ECO’ LED on. Display shows ‘4’ buzzer beeps 4 times. Regeneration valve
open (see ‘Output Indication’ table for details Page 20)
Press ‘PROGRAM’ Button
Display shows ‘5’ buzzer beeps 5 times. Drain Pump on
Press ‘PROGRAM’ Button
Display shows ‘6’ buzzer beeps 6 times. Inlet Valve open (only when P1
level is not detected)
Press ‘PROGRAM’ Button
Display shows ‘7’ buzzer beeps 7 times. Heater on (only when P1 level is
detected)
Press ‘PROGRAM’ Button
Display shows ‘8’ buzzer beeps 8 times. Recirculation Pump on
Press ‘PROGRAM’ Button
Display shows ‘9’ buzzer beeps 9 times. Detergent dispenser open
(dispenser may open up to 20 sec later)
Press ‘PROGRAM’ Button
Display shows ‘10’ buzzer beeps 10 times. Drying Fan on
Press ‘PROGRAM’ Button
‘FRAGILE’ LED on. Display & buzzer showing the last occurred fault
Press ‘PROGRAM’ Button
Repeat
Exit F/O Test
Switch off Power Button
Page 24 DW161
