Guarantee and Guarantee Policy
If any part is found to be defective due to faulty
manufacture within two years of original purchase,
Electrolux Outdoor Products, through its Authorised
Service Repairers will effect the repair or replacement
to the customer free of charge providing:
(a) The fault is reported directly to the Authorised
Repairer.
(b) Proof of purchase is provided.
(c) The fault is not caused by misuse, neglect or
faulty adjustment by the user.
(d) The failure has not occurred through fair wear
and tear.
(e) The machine has not been serviced or repaired,
taken apart or tampered with by any person not
authorised by Electrolux Outdoor Products .
(f) The machine has not been used for hire.
(g) The machine is owned by the original purchaser.
(h) The machine has not been used outside of the
country for which it was specified.
(i)
The machine has not been used commercially.
*
This guarantee is additional to, and in no way
diminishes the customers statutory rights.
Failures due to the following are not covered,
therefore it is important that you read the instructions
contained in this Operator's Manual and understand
how to operate and maintain your machine:
Failures not covered by guarantee
*
Replacing worn or damaged blades.
*
Failures as a result of not reporting an initial fault.
*
Failures as a result of sudden impact.
*
Failures as a result of not using the product in
accordance with the instructions and
recommendations contained in this Operator's
Manual.
*
Machines used for hire are not covered by this
guarantee.
*
The following items listed are considered as
wearing parts and their life is dependent on
regular maintenance and are, therefore not
normally subject to a valid warranty claim:
Blades.
*
Caution!
Electrolux Outdoor Products does not accept
liability under the warranty for defects caused in
whole or part, directly or indirectly by the fitting of
replacement parts or additional parts that are not
either manufactured or approved by Electrolux
Outdoor Products, or by the machine having
been modified in any way
Service Recommendations
•
Your product is uniquely identified by a silver and black product rating label.
•
We strongly recommend that your product is serviced at least every twelve months, more often in a
professional application.
Fault Finding Hints
Lawnmower will not start
1.
Is the correct Starting procedure being followed?
See ‘To Start your Lawnmower’.
2.
Is the safety key correctly located?
3.
Is the battery flat? - Charge the battery - See
‘Battery Charging’.
4.
Has the Safety Key fuse blown? Replace with a
new one.
5.
Has the Overload Cutout operated? See
‘Automatic Overload Cutout’.
If the lawnmower will still not start - remove the
safety key.
Consult your local Approved Service Centre.
Poor Grass Collection
1.
Clean the outside of the air intakes, the discharge
chute and the underside of the deck
.
2.
Raise the height of cut - See ‘Cutting Height
Adjustment’.
If poor collection persists - remove the safety key.
Consult your local Approved Service Centre.
Excessive Vibration
1.
Check that the blade is fitted correctly?
2.
If the blade is damaged or worn, replace it with a
new one.
If vibration persists, immediately - remove the
safety key.
Consult your local Approved Service Centre.
Lawnmower becomes heavy to push
1.
In long grass or uneven ground, the height of cut
should be raised to a higher position. See
‘Cutting Height Adjustment’.
2.
Check that the wheels can rotate freely.
If problem persists - remove the safety key.
Consult your local Approved Service Centre.
Lack of Motor Power, Overheating or Cutting Out
1.
Is the battery flat? - Charge the battery - See
‘Battery Charging’.
2.
Clean grass clippings and debris from around the
motor and air inlets and the underside of the deck
including the chute.
3.
Raise the height of cut - See ‘Cutting Height
Adjustment’.
If the lawnmower still lacks power, is overheating
or cutting out - remove the safety key.
Consult your local Approved Service Centre.
Insufficient Cutting Time
1.
Is the battery fully charged? - See ‘Battery
Charging’.
2.
Raise the height of cut - See ‘Cutting Height
Adjustment’.
3.
Battery needs replacing - See ‘Changing the
Battery’.
If problem persists - remove the safety key.
Consult your local Approved Service Centre.
ENGLISH - 5
