manualshive.com logo in svg

Electrolux GLMV169DB, Service Manual

Share
Download
Electrolux GLMV169DB Service Manual Download Page 22

20

   GLMV169DB
   GLMV169DQ

   GLMV169DS
   PLMV169DC

TEST PROCEDURES

PROCEDURE

LETTER

COMPONENT TEST

6) Re-install the outer case (cabinet).
7) Reconnect the power supply cord after the outer case is installed.
8) Run the oven and check all functions.

2. Control Unit.

The following symptoms  indicate a defective control unit.  Before replacing the control unit, perform
the Key unit test (Procedure M) to determine if control unit is faulty.

2-1 In connection with pads.

a) When touching the pads, a certain group of pads do not produce a signal.
b) When touching the pads, no pads produce a signal.

2-2 In connection with indicators

a) At a certain digit, all or some segments do not light up.
b) At a certain digit, brightness is low.
c) Only one indicator does not light.
d) The corresponding segments of all digits do not light up; or they continue to light up.
e) Wrong figure appears.
 f) A certain group of indicators do not light up.
g) The figure of all digits flicker.

2-3 Other possible problems caused by defective control unit.

a) Buzzer does not sound or continues to sound.
b) Clock does not operate properly.
c) Cooking is not possible.

When testing is completed,

1) Disconnect the power supply cord, and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Reconnect all leads removed from components during testing.
5) Re-install the outer case (cabinet).
6) Reconnect the power supply cord after the outer case is installed.
7) Run the oven and check all functions.

1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. If the display fails to clear when the STOP/CLEAR pad is depressed, first verify the flat ribbon cable

is making good contact, verify that the door sensing switch (stop switch) operates properly; that is the
contacts are closed when the door is closed and open when the door is open. If the door sensing switch
(stop switch) is good, disconnect the flat ribbon cable that connects the key unit to the control unit and
make sure the door sensing switch is closed (either close the door or short the door sensing switch
connecter). Use the Key unit matrix indicated on the control panel schematic and place a jumper wire
between the pins that correspond to the STOP/CLEAR pad making momentary contact. If the control
unit responds by clearing with a beep the key unit is faulty and must be replaced. If the control unit does
not respond, it is faulty and must be replaced. If a specific pad does not respond, the above method
may be used (after clearing the control unit) to determine if the control unit or key pad is at fault.

5. Reconnect all leads removed from components during testing.
6. Re-install the outer case (cabinet).
7. Reconnect the power supply cord

after the outer case is installed.

8. Run the oven and check all

functions.

L

KEY UNIT TEST

G5

5

0

4

9

3

8

2

7

1

6

G6

Auto

Defrost

Night

Light

Clear

Off

Fresh

Veggie

Work

Light

Power

Level

Plus

1 Min

Popcorn

Fan

HI / LO

Turntable

On / Off

Help

Dinner

Items

Lunch

Items

Clock

G7

G8

G9

G10

G11

G12

G13

G1

G2

G3

G4

Timer /

Pause

START

Auto

Fan

Frozen

Snacks

Frozen

Entrees

Breakfast

Items

Poultry

Beverage

Fish

Frozen
Veggie

Speed

Defrost

Baked
Potato

Memory

Cook

Sensor
Reheat

Rice

Ground

Meats

Summary of Contents for GLMV169DB





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands