manualshive.com logo in svg

Electrolux GLMV169DB, Service Manual

Share
Download
Electrolux GLMV169DB Service Manual Download Page 19

17

   GLMV169DB
   GLMV169DQ

   GLMV169DS
   PLMV169DC

1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Before performing this test, make sure that the secondary interlock switch and the primary interlock

relay are operating properly, according to the above Switch Test Procedure. Disconnect the wire
lead from the monitor switch (COM) terminal. Check the monitor switch operation by using the
ohmmeter as follows. When the door is open, the meter should indicate a closed circuit. When the
monitor switch actuator is pushed by a screw driver through the lower latch hole on the front plate of
the oven cavity with the door opened (in this condition the plunger of the monitor switch is pushed in),
the meter should indicate an open circuit. If improper operation is indicated, the switch may be
defective. After testing the monitor switch, reconnect the wire lead to the monitor switch (COM) terminal
and check the continuity of the monitor circuit.

5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
 of the oven cavity with the door opened (in this condition the plunger of the monitor switch is pushed in),

the meter should indicate an open circuit. If improper operation is indicated, the switch may be
defective. After testing the monitor switch, reconnect the wire lead to the monitor switch (COM)
terminal and check the continuity of the monitor circuit.

5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.

H

MONITOR SWITCH TEST

TEST PROCEDURES

PROCEDURE

LETTER

COMPONENT TEST

Primary
Interlock
Switch

Monitor
Switch

Screw Driver

Ohmmeter

Black 

White/White

Summary of Contents for GLMV169DB





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands