Electrolux FC48 Installation Manual Download Page 15 | Manualshive

Page: 15 / 36

background image

05306004

Page

Notice

Date

INSTALLATION

MANUAL

3

6

1004

D0884

6. Installation/

Putting into service

Gas connection

CAUTION

The installation, connection and gas arrival adjustments for the
machine must be done by qualified personnel only.

The customer must install a filter and a manual stop valve on the supply side of the
machine if NATURAL GAS is used.
For BUTANE 28-30 mbar or PROPANE 37 or 50 mbar, the customer must install a
filter, a manual closing valve and a pressure reducer.

Check that the diameter of injectors is adequate for the king of gas of your installation (see
table). The machine is delivered with extra injectors in a plastic envelope. There is also a
sheet metal plate with a cork joint or an adjusting head to feed the machine with another gas.

Connect the installation at the exchanger DN 20 (3⁄4" BSP).

Gas burner

Injectors

Gas admission

«
...
13
14
15
16
17
...
»

Summary of Contents for FC48





































Reviews:

No comments

Related manuals for FC48

Brand: TZS First AUSTRIA Pages: 16

Brand: Maxwell Pages: 44

Brand: Saunatec Pages: 15

Brand: Formawell Beauty Pages: 16

Brand: ARIETE Pages: 93

Brand: Lumme Pages: 11

Brand: Lumme Pages: 34

Brand: Siemens Pages: 32

Brand: Siemens Pages: 118

Brand: Siemens Pages: 150

SensorSream TS12 Series

Brand: Siemens Pages: 152

Brand: Fakir Pages: 24

Brand: Fagor Pages: 62

STIRO GAGGIA CLASSIC

Brand: Gaggia Pages: 27

Brand: Arnica Pages: 12

Brand: Arnica Pages: 16

Brand: TEFAL Pages: 32

Brand: TEFAL Pages: 134

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands