background image

38         www.electrolux.com 

Loosen the ring nut to angle the hose to 

the left or right depending on the position 

of your water tap. Do not place the inlet  

hose downwards. After positioning the 

inlet hose, be sure to tighten the ring nut 

again to prevent leaks.

The end of the drain hose can be 

positioned in three ways:

Hooked over the edge of a sink

, using 

the plastic hose guide supplied with the 

machine.

11.4

 Water Drainage

Fitting Hose Guide

bend 

hose

2. 

Adjust length to suit 

trough.

Pull apart to 

insert hose.

pull hose

1.

 

450 approx.

Hose 

Guide

45°

35°

Push the drain hose onto the spigot 

and secure with a clip, ensure a 

loop is formed in the drain hose to 

prevent waste from the sink 

entering the appliance. 

In a sink, drain pipe branch. 

In this case, make sure the end 

cannot come unhooked when the 

machine will be emptied. This could 

be done by tying it to the tap with a 

piece of string or attaching it to the 

wall.

This branch must be above the trap 

so that the bend is at least 60 cm 

above the ground.

Max. 

90 cm
Min. 

60 cm

Summary of Contents for EWF9043BDWA













































Reviews: