background image

WATER DRAIN HOSE

Use the supplied hose clamp to connect
the water drain hose to the sink.
The highest point of the drain hose must be
no more than 600 mm from the floor and
must have a continuous fall to the plumbing
connection.
The drain hose can be lengthened using
additional lengths and connectors. These
must be purchased from Electrolux Spare
Parts. The extension length must not ex-
ceed 2 metres.
The drain hose must be free of obstruc-
tions.
Remove the sink plug when the appliance
drains the water to prevent that the water
goes back into the appliance.
If you connect the water drain hose to a
trap spigot under the sink, remove the plas-
tic membrane. If you do not remove the
membrane, remaining food can cause a
blockage in the drain hose spigot

The appliance has a security feature to
prevent dirty water going back into the
appliance. If, the spigot of the sink has
a 'non-return valve', this valve can
cause the appliance to drain incorrect-
ly. Remove the non-return valve.

Caution!

 Make sure that the water

couplings are tight to prevent water
leakage.
Ensure that hoses are not bent or
squashed under or behind the appli-
ance.

Once connected the inlet hose to the
water tap, turn the tap on and check
that there are no leaks.

20 

electrolux

Summary of Contents for ESL 67040





























Reviews: