background image

Problem

Possible cause

Possible solution

 

The baskets were not loaded
correctly, water did not touch
all surfaces.

Load the baskets correctly.

 

The spray arms could not turn
freely because of incorrect ar-
rangement of the load.

Make sure that an incorrect ar-
rangement of the load does not
cause a blockage of the spray
arms.

 

The filters are dirty or not as-
sembled and installed correctly.

Make sure that the filters are
clean and correctly assembled
and installed.

 

The quantity of detergent was
not sufficient or missing.

Make sure that the quantity of
detergent is sufficient.

Limescale particles on the
dishes

The salt container is empty.

Fill the salt container with salt
for dishwashers.

 

The water softener is adjusted
on a wrong level.

Adjust the level of the water
softener.

 

The salt container cap is not
closed correctly.

Ensure that the salt container
cap is correctly closed.

There are streaks, milky stains,
or a bluish layer on glasses and
dishes.

Rinse aid dosage is too high.

Decrease the rinse aid dosage.

Dry water drop stains on
glasses and dishes.

Rinse aid dosage is too low.

Increase the rinse aid dosage.

 

The detergent can be the
cause.

Use a different brand of deter-
gent.

The dishes are wet.

You have set a washing pro-
gram without drying phase or
with a decreased drying phase.

Let the door stay ajar for some
minutes before you remove the
dishes.

The dishes are wet and dull.

The rinse aid dispenser is emp-
ty.

Fill the rinse aid dispenser with
rinse aid.

 

The multitab function is activa-
ted (this function automatically
deactivates the rinse aid dis-
penser).

Activate the rinse aid dispenser.

ACTIVATING THE RINSE AID
DISPENSER

1. Switch on the appliance. Make sure that

the appliance is in setting mode.

2. Press and hold buttons (4) and (5) at the

same time until the indicators of buttons
(3), (4) and (5) flash.

3. Release button (4) and button (5).
4. Press button (4).

• The indicators of buttons (3) and (5)

go off.

• The indicator of button (4) continues

to flash.

• The display shows the setting of the

rinse aid dispenser.

Rinse aid dispenser
deactivated

Rinse aid dispenser
activated

5. Press button (4) to change the setting.

The display shows the new adjustment.

6. Switch off the appliance to confirm.

electrolux 

17

Summary of Contents for ESL 67040





























Reviews: