Before using your dishwasher for the first time:
1.
Ensure that the electrical and water connections comply
with the installation instructions
2.
Remove all packaging from inside the appliance
3.
Set the water softener
4.
Pour 1 litre of water inside the salt container and then fill
with salt
5.
Fill the rinse aid dispenser
The water softener
The dishwasher is equipped with a water softener designed to
remove minerals and salts from the water supply, which would
have a detrimental or adverse effect on the operation of the
appliance.
The higher the content of these salts, the harder your water is.
Water hardness is measured in equivalent scales, German
degrees, French degrees and mmol/l (millimol per litre).
The softener should be adjusted according to the hardness of
the water in your area. Your local Water Authority can advise
you on the hardness of the water in your area.
The water softener must be set in both ways: manually, using
the water hardness switch and electronically, using the function
push buttons on the control panel.
a) Setting manually
1.
Open the dishwasher door.
2.
Remove the lower basket from the dishwasher.
3
. Turn the water hardness switch to position 1 or 2 (see
table).
4.
Replace the lower basket.
The dishwasher is factory
set at position 2.
b)Setting electronically
(The dishwasher must be switched off)
The dishwasher is factory set at level 5.
1.
Press the On/Off button. The On/Off indicator light
illuminates (setting mode).
I
f other indicator lights are on, this means that a wash
programme has been selected. The programme must be
cancelled: press simultaneously function buttons
2
and
3
for about 2 seconds. All the indicator lights will turn off
(except for the On/Off indicator light and eventually
salt and rinse aid indicator lights) indicating that the setted
programme has been cancelled and the machine is now in
setting mode.
2.
Press simultaneously function buttons
2
and
3
, until the
indicator lights of function buttons
1
,
2
,
3
and
4
start
flashing.
3.
Press the function push button
1
, the indicator lights of
function buttons
2
,
3
and
4
turn off while the indicator
light of button
1
goes on flashing, the digital display
indicates the current level.
Exampel:
= level 5
4.
To change the level, press push button
1
. Each time the
button is pressed the level changes. (For the selection
of the new level see the chart).
Examples:
if the current level is 5, by pressing button
1
once,
level 6 is selected.
if the current level is 10, by pressing button
1
once,
level 1 is selected.
5.
To memorise the operation, switch off the dishwasher by
pressing the On/Off button or wait about 60 seconds
after which the dishwasher will automatically return to
setting mode.
Prior to using for the first time
28
AA07
°dH
(german degrees)
°TH
(french degrees)
mmol/l
(millimol per litre,
international unit for the
hardness of water)
Range
manually
electronically
51 - 70
43 - 50
37 - 42
29 - 36
23 - 28
19 - 22
15 - 18
11 - 14
4 - 10
< 4
9,0 - 12,5
7,6 - 8,9
6,5 - 7,5
5,1 - 6,4
4,0 - 5,0
3,9 - 3,3
2,6 - 3,2
1,9 - 2,5
0,7 - 1,8
< 0,7
IV
IV
IV
IV
IV
III
III
II
I/II
I
91 - 125
76 - 90
65 - 75
51 - 64
40 - 50
33 - 39
26 - 32
19 - 25
7 - 18
< 7
2
2
2
2
2
2
1
1
1
1
level 10
level 9
level 8
level 7
level 6
level 5
level 4
level 3
level 2
level 1
yes
yes
yes
yes
yes
yes
yes
yes
yes
no
Water hardness
Adjusting the
water hardness setting
Level indicated
in the
digital display
Use
of salt