12
www.electrolux.com
ENGLISH
Thank you for choosing an Electrolux ERGORAPIDO® vacuum cleaner.
In order to ensure the best results, always use original Electrolux
accessories and spare parts. They have been designed especially for
your vacuum cleaner. This product is designed with the environment
in mind. All plastic parts are marked for recycling purposes.
DESCRIPTION OF ERGORAPIDO®
A. ON/OFF button
B. Power regulation button
C. ON/OFF button, hand unit
D. Locking screw
E. Release button, hand unit
F. Charging station, wall unit
G. Charging station, floor unit
H. Charging adapter
I. Fine filter (inner filter)
J. Pre filter (outer filter)
K. Release button, dust container
L. Dust container
M. Dusting brush
N. Crevice nozzle
O. Cable protector grill
P. Hatch cover for brush roll
Q. Brush roll
R. BRUSHROLLCLEAN® pedal
S. Nozzle front lights
T. Charging indicator
U. Cliff hanger
V. Slot for accessory storage
BEFORE STARTING
Check that the package includes all parts described in this instruction
manual and read this manual carefully. Pay special attention to the
safety precautions chapter. Save these instructions.
Picture page 2
1
Assemble the handle.
2
Assemble the charge stand.
3
There is a hollow space in the bottom of the charging station where
unused cable can be wound. Insert the adaptor into the mains and
position the charging station on a stable and horizontal surface away
from heat sources, direct sunlight or wet places.
4
The charging indicator will be lit when ERGORAPIDO® is placed in the
charging station.
Picture page 3
CHARGING ERGORAPIDO®
5
When fully charged, the charging indicator will blink slowly. The num-
bers of LED lamps will indicate the level of charge. Full charging time is
around 4 hours. For better battery performance, charge ERGORAPIDO®
for 24 hours before first use and always keep it on charge when not
used.
VACUUMING WITH ERGORAPIDO®
Before vacuuming, check that the nozzle wheels and the brush roll are
clean from sharp objects in order to avoid scratching sensitive floors
and to ensure full cleaning performance.
6
Start and stop ERGORAPIDO® by pushing the ON/OFF button.
ERGORAPIDO® will start on the high power mode.
For more silent cleaning and longer runtime, press the power
regulation button.
VACUUMING FURNITURE, CAR SEATS ETC.
7
Press the button to release the hand unit from the main body.
8
Attach the crevice nozzle to facilitate cleaning of areas difficult to reach.
Attach the brush on the crevice nozzle for dusting.
9
The crevice nozzle and small brush can be stored in the charging
station or in the slot on the back side of the handle.
BRUSHROLLCLEAN® FUNCTION
Use the BRUSHROLLCLEAN® function to keep the brush roll clean and
free from hair and fibres. For best results use the BRUSHROLLCLEAN®
function when ERGORAPIDO® is fully charged.
10
Place ERGORAPIDO® on a hard and flat surface. Do not use the
BRUSHROLLCLEAN® function on carpets.
Press the BRUSHROLLCLEAN® pedal with your foot while the cleaner is
on. Hold for 5 seconds until hairs and fibres are removed. There will be
a cutting noise during this process, this is normal. If hairs remain on the
brush roll, repeat the process.
The BRUSHROLLCLEAN® function is equipped with an overheating
protection. If the BRUSHROLLCLEAN® function has been used for more
than 30 seconds (constant or interrupted) it will deactivate the brush
roll and turn off the nozzle front lights. The vacuum cleaner can still
be used, even when the BRUSHROLLCLEAN
®
function is deactivated.
To reactivate the BRUSHROLLCLEAN® function, place ERGORAPIDO
®
on
charge and charge for 15 minutes.
Please note that the BRUSHROLLCLEAN® function might not be able to
remove thicker threads or wires that are caught in the brush roll.
EMPTYING OF THE DUST CONTAINER
11
Remove the dust container by pressing the buttons.
12
Take out the filters from the dust container by pressing the release but-
tons. Empty the contents into a dustbin. Never wash the dust container
or filters in a dishwasher.
IMPORTANT - FILTER CLEANING!
13
The filters must be cleaned at regular intervals to ensure a high clean-
ing performance. Take out the filters by pressing the release buttons.
Separate the inner filter from the outer filter.
14
Rinse the filter parts carefully under lukewarm water without using any
detergents. (Never use the dishwasher or washing machine.) Shake to
remove excess water and leave to dry minimum 12h before putting
them back into the cleaner.
CLEANING THE HOSE AND NOZZLE WHEELS
15
Loosen the hose behind the nozzle from its upper connection. Remove
any object or debris that can be blocking the airflow in the hose or in
the air channel to the dust cup, and put the hose back.
16
If the wheels need to be cleaned or get jammed, remove them carefully
by using a flat screwdriver.
REMOVING AND CLEANING THE BRUSH ROLL
17
If the brushroll gets blocked ERGORAPIDO® will stop. Open the cable
protector grill and the brush roll hatch cover and remove the brush roll.
18
Use a pair of scissors to remove threads etc. Reassemble the brush roll,
making sure it can spin freely.
REMOVING THE BATTERIES FOR RECYCLING
Warning; Battery removal must only be done by an Electrolux
service center or official collection point!
19
Only remove batteries if the product is to be scrapped. Improper
handling of the batteries may be hazardous. Batteries should always
be completely discharged before removal. Take your product to an
Electrolux service center or official collection point for recycling. They
can remove and recycle the battery and electric parts in a safe and
professional way. Follow your country’s rules for collection of recharge-
able batteries and electrical products.
Enjoy a great cleaning experience with ERGORAPIDO®!
Electrolux reserves the right to change products, information and
specifications without notice.
