3
CONTENTS
Warnings
.................................................................................................................................................
2
Use
- Cleaning the interior - Control panel - Freezer section ...................................................................
4
Use
- Startup and temperature adjustment - Freezing fresh food - Conservation of deep-frozen food ....
Ice-cube production - Thawing ..................................................................................................................
5
Use
- Fridge section - Startup and temperature adjustment - Fresh food refrigeration - Movable shelves
6
Use
- Positioning the door shelves- Bottle holder - Drawer - Humidity control .........................................
7
Hints
- Hints for refrigeration - Hints for freezing - Hints for storage of frozen food .................................
8
Maintenance
- Periodic cleaning - Periods of non-operation - Illumination lamp...................................... 9
Maintenance
- Defrosting ....................................................................................................................... 10
Noisinnes - Customer service and spare parts
................................................................................... 11
Technical information
/
Installation -
Location - Shelf holders............................................................... 12
Installation -
Rear spacers - Electrical connection ................................................................................... 13
Installation -
Changing the opening direction of the doors....................................................................... 14
•
Do not place carbonated or fizzy drinks in the
freezer as it creates pressure on the container,
which may cause it to explode, resulting in
damage to the appliance. Do not use a
mechanical device or any artificial means to
speed up the thawing process other than those
recommended by the manufacturer. Never use
metal objects for cleaning your appliance as it
may get damaged.
Installation
• During normal operation, the condenser and
compressor at the back of the appliance heat up
considerably. For safety reasons, minimum
ventilation must be as shown in the instructions.
Attention: keep ventilation openings clear of
obstruction.
• Care must be taken to ensure that the appliance
does not stand on the electrical supply cable.
Important:
if the supply cord is damaged, it must
be replaced by a special cord or assembly availa-
ble from the manufacturer or its service agent.
• If the appliance is transported horizontally, it is
possible that the oil contained in the compressor
flows in the refrigerant circuit. It is advisable to
wait at least two hours before connecting the
appliance to allow the oil to flow back in the
compressor.
• There are working parts in this product which
heat up. Always ensure that there is adequate
ventilation as a failure to do this will result in
component failure and possible food loss. See
installation instructions.
• Parts which heat up should not be exposed.
Wherever possible the back of the product should
be against a wall.
Environment Protection
This appliance does not contain gasses which
could damage the ozone layer, in either its
refrigerant circuit or insulation materials. The
appliance shall not be discarded together with
the urban refuse and rubbish. Avoid damaging
the cooling unit, especially at the rear near the
heat exchanger. Information on your local
disposal sites may be obtained from municipal
authorities. The materials used on this appliance
marked by the symbol
are recyclable.
14
Changing the opening direction of
the doors
Before carrying out any operations, remove the plug
from the power socket.
To change the opening direction of the door,
proceed as follows:
1.
pull off the ventilation grille (D) which is clipped
into place;
2.
remove the bottom hinge (E) by unscrewing its
fixing screws;
3.
remove the lower door, sliding it out of the
middle hinge;
4.
unscrew the middle hinge (H);
5.
remove the upper door, releasing it from the
upper pin (G);
6.
unscrew the upper pin (G) and refit it on the
opposite side;
7.
remove the two plugs of the door (where
available), discovering the holes for the hinge
pins, assemble them on the opposite side and
refit the upper door;
8.
reassemble the middle hinge on the opposite
side;
9.
reassemble the lower door;
10. using a 10 mm spanner, unscrew the hinge pin
(E) and reassemble it on the opposite side of the
hinge;
11. reassemble the lower hinge (E) on the opposite
side, using the screws previously removed. Slide
the hole cover (F) out of the ventilation grille (D)
by pushing it in the direction of the arrow and
reassemble it on the opposite side;
12. refit the ventilation grille (D), clipping it into
place.
13. Unscrew the handles. Re½t them on the
opposite side.
To line up the doors, it is possible to adjust the
middle hinge (H) horizontally by means of a tool,
after slackening the two screws (see figure).
Warning:
After having reversed the opening direction of
the doors check that all the screws are properly
tightened and that the magnetic seal adheres to
the cabinet.
If the ambient temperature is cold (i.e.
in Winter), the gasket may not fit perfectly to the
cabinet. In that case, wait for the natural fitting of the
gasket or accelerate this process by heating up the
part involved with a normal hairdrier.
H
G
F
F
D
F
F
E
E
