Electrolux EI23BC37SS4 Use And Care Manual Download Page 26 | Manualshive

Page: 26 / 44

background image

26

Dispenser Model

Automatic Ice Maker/Water Dispenser

Adjusting Ice Bin Auger

Auger

IMPORTANT

When removing or replacing the ice bin,

DO NOT rotate the auger in the ice bin.

If the auger is accidentally rotated, you

must realign the auger by turning it in 45

degree turns (see below) until the ice bin

fits into place with the drive mechanism.

If the auger is not properly aligned when

replacing the ice bin, the refrigerator will

not dispense ice. The fresh food door

also may not close properly causing

warm air to leak into the fresh food

compartment.

NOTE

Dispenser models allow for an additional

freezer ice maker to be installed. Call

1-877-435-3287 for more information.

«
...
24
25
26
27
28
...
»

Summary of Contents for EI23BC37SS4













































Reviews:

No comments

Related manuals for EI23BC37SS4

Brand: GE Pages: 20

Brand: V-ZUG Pages: 52

Brand: Saivod Pages: 26

Brand: Iceco Pages: 24

Brand: ZANKER Pages: 14

Brand: Gorenje Pages: 34

Brand: Continental Refrigerator Pages: 2

Brand: Zanussi Electrolux Pages: 16

Brand: MATOS Pages: 18

Brand: U-Line Pages: 57

Brand: Kalamera Pages: 11

Brand: Fagor Pages: 19

170 L COLD GOLD DELUXE

Brand: Godrej Appliances Pages: 20

Brand: THOMSON Pages: 85

Brand: Delfield Pages: 4

Brand: Indesit Pages: 16

Le Maitre JKG1450

Brand: JUNO Pages: 12

Brand: Galanz Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands