background image

Always light the burner before you put
cookware.

To light the burner:
1. Turn the control knob counterclockwise

to the maximum position ( 

 

 ) and

push it down.

2. Keep the control knob pushed for ap-

proximately 5 seconds; this will let ther-
mocouple to warm up. If not, the gas
supply will be interrupted.

3. Adjust the flame after it is regular.

If after some tries the burner does not
light, check if the crown and its cap are
in correct positions.

3

4

2

1

1

Burner cap

2

Burner crown

3

Ignition candle

4

Thermocouple

Warning!

 Do not keep the control

knob pushed for more than 15
seconds.
If the burner does not light after 15
seconds, release the control knob, turn
it into off position and try to light the
burner again after minimum 1 minute.

Important!

 In the absence of electricity you

can ignite the burner without electrical
device; in this case approach the burner

with a flame, push the relevant knob down
and turn it counter-clockwise to maximum
gas release position.

If the burner accidentally goes out, turn
the control knob to the off position and
try to light the burner again after mini-
mum 1 minute.

When switching on the mains, after in-
stallation or a power cut, it is quite nor-
mal for the spark generator to be acti-
vated automatically.

Turning the burner off

To put the flame out, turn the knob to the
symbol 

 .

Warning!

 Always turn the flame down

or switch it off before removing the
pans off the burner.

Operating electric zones

To switch on and increase the heat setting
turn the knob clockwise. To decrease the
heat setting turn the knob counter-clock-
wise. To switch off turn the knob to the 0.

When a cooking zone operates, it
hums for a short time. This is typical of
all ceramic glass cooking zones and
does not show that the appliance oper-
ates incorrectly.

Examples of cooking applications

Heat

setting:

Use to:

 1

Keeping warm

2

Gentle simmering

3

Simmering

4

Frying / browning

5

Bringing to the boil

6

Bringing to the boil / quick frying /

deep-frying

HELPFUL HINTS AND TIPS

Energy savings

• If possible, always put the lids on the

pans.

• When the liquid starts to boil, turn down

the flame to barely simmer the liquid.

Warning!

 Use pots and pans with

bottom applicable to the dimension of
burner.
Do not use cooking vessels on the hot-
plate that overlap its edges.

electrolux

Summary of Contents for EHM 6335

















Reviews: