19
Something not working
If the appliance doesn't work properly check the
following points before asking for service:
The flow of gas seems abnormal
Make sure that:
the flame speader holes are not obstructed;
the pressure regulator is working;
the bottle valve is completely open.
Gas smell in the room
Make sure that:
the gas valve is not open;
the gas supply tube is well positioned and in good
condition; remember to replace it at least once a
year.
The oven doesn't heat
Make sure that the oven knobs are in the correct
working positions.
Cooking time is too long
Check that the temperature is correct for the type of
food to be cooked.
The cooker produces smoke
We advise you to clean the oven after use. Splashes
of fat can occur during the cooking of meat and, if
the oven isn't cleaned properly, these produce smoke
and bad smell. (see paragraph concerning cleaning).
The oven lamp doesn't work
The lamp has burnt out. To replace it follow the
instructions given in the relative paragraph.
If, after following all the above checks the appliance still
doesn't work, call your nearest Service Centre giving
them all the necessary information, such as model and
serial number of the appliance.
Never look for an escape of gas with a
match; use instead soap and water.
Maintenance -Technical assistance
The gas cocks must be periodically lubricated to ensure good
working and safety. Maintenance should be performed as
follows:
Remove the knob and panel after having taken out
fastening screws.
Loosen the two screws located at the sides of the cock bar.
Remove the cone and clean it carefully.
Then, apply a thin layer of grease non soluble in water,
suitable for gas cocks. Take care not to obstruct the gas
flow holes by an excess of grease.
Reassemble the whole with utmost care performing the
operations described above inversely.
Original spare parts
This machine, before leaving the factory, has been tested and
studied by many experts and specialists, in order to give you
the best results. Any repair work which needs to be carried out
should be done with the utmost care and attention. For this
reason we reccomend that for any problem you contact the
dealer who sold it to you, or our nearest authorized Service
Centre, specifying the nature of the problem and the particular
model which you own.
The guarantee
Your new cooker is covered by guarantee. You will find the
guarantee certificate enclosed. If you are missing anything,
contact your retailer, giving the date of purchase, model, and
the registration number which is printed on the identification
plate.We ask you to bear in mind that for the guarantee to be
operated, it is necessary to fill in and send the larger part of
the guarantee to Electrolux Technical Assistance & Service
within 8 days of purchase, so that we can provide registration.
We advise you that the smaller part of the certificate, as well
as your receipt and proof of purchase, should be shown when
required to personnel of Electrolux Technical Assistance &
Service. Without following this procedure, the repair personnel
will have to charge you more for the repair.
Electrical connection
The unit is preset to work with a voltage of single phase
230 V.
Before making the connection make sure that: the
energy power available in the user's house is sufficient
for the normal supply of this appliance (see rating plate).
The unit is correctly connected to earth through a
suitable plug and according to the installation country
Laws.
The socket or the omnipolar switch used for the
connection must be easilv reached with the installed
appliance. The appliance is supplied with the electric
cord: consequently, you have to install a plug fit for the
load shown in the serial number plate. The plug has to
be connected to an adequate socket.
If you wish to directly connect to the mains, you have to
interpose an omnipolar switch with a minimum opening
between contacts of 3 mm, between the unit and the
mains, complying with the existing regulations. The
brown live wire (originating from the clamp of the cooker
junction box) must always be connected to the phase
of the mains supply. In any case, the supply cord must
be positioned in such a way as it doesn't reach in any
Fig. 31
point a temperature higher by 50°C than the room tem-
perature.
Should the supply cord need to be replaced, it is
necessary that the yellow/green earth wire is about 2cm
longer than the live and neutral ones (Fig. 31).
After the connection, test the heating elements for about
3 minutes to ensure that they are working correctly.
The manufacturer refuses any responsability in
cases where normal safety measures are not
observed.
FO 0480
Ground (yellow - green)
Neutral
wire
Phase