background image

15 Prism

rotations

0-127

128-190

191-192

193-255

Prisms angle adjustment

Counterclowckwise rotation from fast to slow

no function

Clockwise rotation from slow to fast

16 Frost

0-127

128-255

No function

Frost effect

17 Reset

0-25

26-76

77-127

128-240

241-255

No function

Reset : color wheels/gobos/Prism/focus/Zoom

Rest : Pan/Tilt

General reset

No function

5. Troubleshooting

A. The moving head does not work, no lights nor fan :

1.

Check the power cord and the main fuse.

2.

Check that your electrical system is working.

B. No response to DMX controller

1.

A dot must flash on the device control screen. If it’s not the case, check if cables 
are properly connected and in good condition.

2.

If the dot flashes, check your addressing as well as the polarity of your DMX 

wiring.

3.

Try an other DMX controller

4.

Avoid to lay your DMX cables alongside high-voltage lines to avoid interference. 

6. Cleaning

Before any cleaning operation, unplug the moving head power cord in order to avoid 
any electrocution hazard. Cleaning the optic must be done periodically in order to 
optimize the moving head’s brightness. The cleaning frequency depends on the 
operating environment. Smoke and dust may cause a large accumulation of dirt upon 
the moving head’s optics : 

-

Clean it with a soft dry cloth.

-

Do not use liquid or detergent products.

Clean external lenses approximately every 20 days, with a soft dry cloth, without 

overly pressing on the lenses.

ELECTROCONCEPT SARL LA GARE 69620 CHAMELET FRANCE

9

Summary of Contents for M SPOT 200II










Reviews: