background image

Electro-Voice Live X Series Passive Owner’s Manual

15

Troubleshooting

Problem

Possible Cause(s)

Action

1. No Sound

Amplifier

Connect a known working test speaker to the amplifier outputs. If there is no 

sound, check that all the electronics are on, the signal routing is correct, the 

source is active, the volume is turned up, and so on. Correct/repair/replace 

as necessary. If there is sound, the problem is in the wiring.

Wiring

Verify that you have connected the correct wire pairs to the amplifier. Play 

something at low level through the amplifier (for example, from a CD player 

or tuner). Connect the test speaker in parallel with the malfunctioning line. If 

the sound level has gone or is very weak, the line has a short in it (possibly a 

severe scrape, pinch, or staple puncture). If the sound level is normal, the 

wire is open (possibly a cut wire or a missed connection). Using the test 

speaker, move down the line and test each connection/junction until you find 

the problem and correct it. Observe proper polarity.

2. Poor Low

Frequency 

Response

Speakers wired 

out-of-polarity

When two speakers are connected out of polarity, the low frequencies will 

cancel each other acoustically. Carefully observe the wire markings or tracers 

on your speaker wires. Verify that the amplifier (+) terminal is connected to pin 

1+ of the NL4 connector and the amplifier (-) terminal is connected to pin 1- 

of the NL4 connector.

3. Intermittent output 

such as crackling 

or distortion

Faulty Connection

Check all connections at amplifier and speakers to ensure they are all clean 

and tight. If the problem persists, it may be in the amplifier or wiring.

See Problem 1 above.

4. Constant noise 

such as buzzing, 

hissing, humming

Defective amplifier 

or other electronic 

device

If the noise is present but no program material is playing, the likely cause is 

the signal chain in the electronics. Evaluate each component as necessary to 

isolate the problem.

Poor system 

grounding or 

ground loop

Check and correct the system grounding, as required.

If these suggestions do not solve your problem, contact your nearest Electro-Voice dealer or Electro-Voice distributor.

Summary of Contents for Live X ELX 112

















Reviews: