background image

 

Page 1 of 2 

XX017 

 

Electro Industries, Inc.  

Limited Product Warranty 

Effective February 5, 2009 

 
Electro Industries, Inc. warrants to the original owner, at the original installation site, for a period 
of two (2) years from date of installation, that the product and product parts manufactured by 
Electro Industries are free from manufacturing defects in materials and workmanship, when 
used under normal conditions and when such product has not been modified or changed in any 
manner after leaving the plant of Electro Industries.  If any product or product parts 
manufactured by Electro Industries are found to have manufacturing defects in materials or 
workmanship, such will be repaired or replaced by Electro Industries.  Electro Industries shall 
have the opportunity to directly, or through its authorized representative, examine and inspect 
the alleged defective product or product parts.  Electro Industries may request that the materials 
be returned to Electro Industries at the owner’s expense for factory inspection.  The 
determination as to whether product or product parts shall be repaired, or in the alternative 
replaced, shall be made by Electro Industries or its authorized representative.  Electro Industries 
will cover reasonable labor costs to repair defective product or product parts for ninety (90) days 
after installation. 
 

TWENTY YEAR (20) LIMITED WARRANTY ON BOILER ELEMENTS AND VESSELS 

 
Electro Industries, Inc. warrants that the boiler elements and vessels of its products are free 
from defects in materials and workmanship through the twentieth year following date of 
installation.  If any boiler elements or vessels are found to have a manufacturing defect in 
materials or workmanship, Electro Industries will replace them. 

 

TWENTY YEAR (20) LIMITED WARRANTY ON SPIN FIN ELEMENTS 

 
Electro Industries, Inc. warrants that the spin fin elements of its products are free from defects in 
materials and workmanship through the twentieth year following date of installation.  If any spin 
fin elements are found to have a manufacturing defect in materials or workmanship, Electro 
Industries will replace them. 

 

FIVE YEAR (5) LIMITED WARRANTY ON OPEN WIRE ELEMENTS 

 
Electro Industries, Inc. warrants that the open wire elements of its products are free from 
defects in materials and workmanship through the fifth year following date of installation.  If any 
open wire elements are found to have a manufacturing defect in materials or workmanship, 
Electro Industries will replace them. 

Summary of Contents for Mini-Boiler BH309



















Reviews: