ELECTRO FREEZE 876, Operator'S Manual

Page: 36 / 82

123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
ELECTRO FREEZE Models 876, 876B, 876C, 876RH, 876BRH, 876CRH
28
184633
12 Troubleshooting Tables
PROBLEM PROBABLE CAUSE REMEDY
Models 876RH and 876BRH Only
(Refrigerated Hopper-RH)
1. Insufficient supply of mix. 1. Fill hopper at least 1/3 full – keep
hopper this full at all times.
2. Improper mixing of product. Brix too low. 2. Follow mixing instructions on product
label. See Section 10.2, Adjusting
Product Consistency.
3. Worn blades. 3. Replace blades.
4. Freezer not level. 4. Level freezer.
Freezer
vibrates.
5. Low on refrigerant. 5. Contact your Electro Freeze Distributor
for service
1. Dirty or blocked condenser, restricted air
flow and/or high room temperature. 1. Remove obstruction and/or lower room
temperature. Have condenser cleaned
by your Electro Freeze Distributor.
2. Dispensing too much product too fast. 2. Check freezer capacity rating.
3. Product too warm going into freezer. 3. Precool – DO NOT FREEZE.
Poor or slow
product
recovery.
4. Component failure. 4. Contact your Electro Freeze Distributor
for service
Product in
hopper freezes. 1. Component out of adjustment or
component failure. 1. Contact your Electro Freeze Distributor
for service
1. Product put in hopper was not precooled. 1. Precool product – DO NOT FREEZE. Product
temperature in
hopper rises
above 45°F.
2. Component out of adjustment or
component failure 2. Contact your Electro Freeze Distributor
for service.