background image

12 

 

OPERATION 

 

Push button

 for model eiQCHC60W 

 

1.  Push stop button, and the motor will stop. 

2.  Push the Low button, and the motor runs at low speed. 

3.  Push the high button, and the motor runs at mid speed. 

4.  Push the High button, and the motor runs at high speed. 

5.  Push the light button and the two lights will come on. Push it again and the 

light will turn off. 

 

     

 

 
 

   

 
MAINTENANCE 

   

Before cleaning, switch the unit off and pull out the plug, or switch off at the 

relevant mains switch if the unit has been hard-wired in. Make sure the unit 

has no power being fed to it. 

 

   

I.  Regular Cleaning   

 

Use a soft cloth moistened with hand-warm mildly soapy water or household 

cleaning detergent. Never use metal pads, chemicals, abrasive material or a 

stiff brush to clean the unit.   

 

Note! Do not use a steam-cleaner to clean the hood; electrical components 

could be damaged or short-circuit as a result. 

 

   

II. Monthly Cleaning for metallic anti-grease filter 

 

ESSENTIAL NOTE: Clean the filter every month; an excessive build-up of 

grease can become a fire hazard. The filter collects grease, smoke and 

dust…... so the filter directly affects the efficiency of the cooker hood. If it’s not 

cleaned, the grease residue (potentially flammable) will saturate on the filter.   

 

 

Summary of Contents for eiQCHC60W

















Reviews: