Electricwingman FlightClub PROton Builder'S Manual Download | Manualshive

Page: 6 / 20

background image

www.electricwingman.com

The firmware should flash but if it is the first time Butterflight has been flashed the
board may not go into DFU mode (because it does not match the existing firmware),
this can be fixed by either using the boot button when you plug the USB in or by
using Betaflight configurator and using the DFU command then switching to the
Butterflight configurator.

The latest version of Butterflight will then flash to the board.

Make use the com port is shown at the top and then click on Connect

Go to the ports tab and set UART1 to Serial rx and click Save and Reboot

«
...
4
5
6
7
8
...
»

Summary of Contents for FlightClub PROton





















Reviews:

No comments

Related manuals for FlightClub PROton

Brand: Veeniix Pages: 44

Brand: Protocol Pages: 9

Brand: Emax Pages: 17

DJI Mavic NDVI Single Upgrade

Brand: Sentera Pages: 26

Brand: XciteRC Pages: 16

Brand: XciteRC Pages: 8

16002050 Walkera Tali H500 Hexacopter RTF GoPro

Brand: XciteRC Pages: 24

Brand: XciteRC Pages: 40

Brand: XciteRC Pages: 43

Brand: Hubsan Pages: 24

RedEdge-M Quick Mount Kit for DJI Inspire 1

Brand: MicaSense Pages: 9

RedEdge-MX DJI Inspire 2 Quick Mount

Brand: MicaSense Pages: 13

RedEdge-MX DJI Matrice 100/600 Series Quick Mount Gen. 2

Brand: MicaSense Pages: 14

RedEdge-M DJI Matrice 100 Fixed Mount

Brand: MicaSense Pages: 14

Brand: Botlink Pages: 10

Brand: Botlink Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands