background image

 3

GB-031C/f.347

INTRODUCTION

Please read and follow the installation and operating instructions 

carefully,  to  ensure  the  long  life  and  reliable  operation  of  this 

appliance.

The  Electric  Heating  Company  may  make  minor  changes 

if  necessary  in  the  appliance  that  will  not  be  shown  in  the 

operating instructions, so long as the main features of the boiler 

remain the same.

All  boilers  come  with  a  24  month  warranty  that  covers  all 

defects originating from faulty materials and workmanship in the 

manufacture of the boilers.

The  warranty  covers  the  replacement  of  any  faulty  parts  and 

labour costs.

The warranty will not cover any damage to the boiler from poor 

or incorrect installation work.

The warranty will not cover any call out charges that have not 

been organised by the Electric Heating Company Ltd.

The  warranty  will  not  cover  water  leaks  into  the  boiler.  All 

plumbing joints must be checked.

The  warranty  card  must  be  completed  and  sent  back  to  The 

Electric Heating Company as soon as possible for registration.

An internal Magnetic Filter is fitted to the Boiler and it must be 

cleaned  at  least  annually.  (Note:  Failure  to  clean  the  Magnetic 

Filter may result in boiler shutdown). Warranty calls will not be 

covered for this repair.   

 

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental cap-

abilities, or lack of experience  and knowledge, unless they have been given supervision or instruction concerning use 

of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

Page Contents

INTRODUCTION   

 

 

 

 

3

PREPARATION 

 

 

 

 

 

4

INSTALLATION 

 

 

 

 

 

5

ELECTRICAL CONNECTIONS AND CONTROLS 

9

EXTERNAL CONTROL WIRING   

 

 

11

CONTROL PANEL CONNECTIONS 

 

 

12

EXTERNAL BOILER WIRING 

 

 

 

13 

BOILER DIMENSIONS 

 

 

 

 

13

USER INSTRUCTIONS 

 

 

 

 

15

FAULT FINDING 

 

 

 

 

 

16

TECHNICAL SPECIFICATIONS 

 

 

 

17

Summary of Contents for EHCCOM12KW





















Reviews: