Electra Amsterdam Series Owner'S Manual Download Page 7

8

9

control. To make sure that you can slow down and stop safely in wet conditions, 

ride more slowly and apply your brakes earlier and more gradually than you 

would under normal, dry conditions.  See also Section 4.C.

E.  Night Riding

  Riding a bicycle at night is 

much

 more dangerous than riding during the day. A 

bicyclist is very difficult for motorists and pedestrians to see. Therefore, children 

should never ride at dawn, at dusk or at night.  Adults who chose to accept the 

greatly increased risk of riding at dawn, at dusk or at night need to take extra 

care both riding and choosing specialized equipment which helps reduce that 

risk. Consult your dealer about night riding safety equipment.

 

  WARNING: Reflectors are not a substitute for required lights. Riding 

at dawn, at dusk, at night or at other times of poor visibility without 

an adequate bicycle lighting system and without reflectors is 

dangerous and may result in serious injury or death.

  Bicycle reflectors are designed to pick up and reflect car lights and street lights 

in a way that may help you to be seen and recognized as a moving bicyclist.  

   CAUTION: Check reflectors and their mounting brackets regularly to 

make sure that they are clean, straight, unbroken and securely 

mounted.  Have your dealer replace damaged reflectors and 

straighten or tighten any that are bent or loose.

  The mounting brackets of front and rear reflectors are often designed as brake 

straddle cable safety catches which prevent the straddle cable from catching on 

the tire tread if the cable jumps out of its yoke or breaks.

   WARNING: Do not remove the front or rear reflectors or reflector 

brackets from your bicycle. They are an integral part of the bicycle’s 

safety system. 

  Removing the reflectors reduces

 

your visibility to others using the 

roadway. Being struck by other vehicles may result in serious injury or 

death. 

  The reflector brackets may protect you from a brake straddle cable 

catching on the tire in the event of brake cable failure. If a brake straddle 

cable catches on the tire, it can cause the wheel to stop suddenly, causing 

you to loose control and fall.

  If you choose to ride under conditions of poor visibility, check and be sure 

you comply with all local laws about night riding, and take the following strongly 

recommended additional precautions:

  • Purchase and install battery or generator powered head and tail lights which 

meet all regulatory requirements and provide adequate visibility.

  • Wear light colored, reflective clothing and accessories, such as a reflective 

vest, reflective arm and leg bands, reflective stripes on your helmet, flashing 

lights attached to your body and/or your bicycle ... any reflective device or light 

source that moves will help you get the attention of approaching motorists, 

pedestrians and other traffic.

  • Make sure your clothing or anything you may be carrying on the bicycle does 

  13. Don’t weave through traffic or make any moves that may surprise people 

with whom you are sharing the road.

  14. Observe and yield the right of way.

  15. Never ride your bicycle while under the influence of alcohol or drugs.

  16. If possible, avoid riding in bad weather, when visibility is obscured, at 

dawn, dusk or in the dark, or when extremely tired. Each of these conditions 

increases the risk of accident. 

C.  Off Road Safety

   We recommend that children not ride on rough terrain unless they are 

accompanied by an adult. 

  1. The variable conditions and hazards of off-road riding require close attention 

and specific skills. Start slowly on easier terrain and build up your skills. If your 

bike has suspension, the increased speed you may develop also increases your 

risk of losing control and falling. Get to know how to handle your bike safely 

before trying increased speed or more difficult terrain.

  2. Wear safety gear appropriate to the kind of riding you plan to do.

  3. Don’t ride alone in remote areas. Even when riding with others, make sure 

that someone knows where you’re going and when you expect to be back.

  4. Always take along some kind of identification, so that people know who you 

are in case of an accident; and take along some cash for food, a cool drink or an 

emergency phone call.

  5. Yield right of way to pedestrians and animals. Ride in a way that does not 

frighten or endanger them, and give them enough room so that their unexpected 

moves don’t endanger you.

  6. Be prepared. If something goes wrong while you’re riding off-road, help may 

not be close.  

  7. Before you attempt to jump, do stunt riding or race with your bike, read and 

understand Section 2.F.

Off Road respect

  Obey the local laws regulating where and how you can ride off-road, and 

respect private property. You may be sharing the trail with others — hikers, 

equestrians, other cyclists. Respect their rights. Stay on the designated trail. 

Don’t contribute to erosion by riding in mud or with unnecessary sliding. Don’t 

disturb the ecosystem by cutting your own trail or shortcut through vegetation 

or streams. It is your responsibility to minimize your impact on the environment. 

Leave things as you found them; and always take out everything you brought in.

D.  Wet Weather Riding

   

WARNING: Wet weather impairs traction, braking and visibility, both 

for the bicyclist and for other vehicles sharing the road. The risk of an 

accident is dramatically increased in wet conditions.

 

  Under wet conditions, the stopping power of your brakes (as well as the 

brakes of other vehicles sharing the road) is dramatically reduced and your tires 

don’t grip nearly as well. This makes it harder to control speed and easier to lose 

Summary of Contents for Amsterdam Series
































Reviews: