background image

13 

 

 

NOTE: 

Pinch  the  blue  lamp  holder  shroud  as  you  reassemble  the  unit  to  release  any 
trapped  air.  Failure  to  release  the  trapped  air  may  cause  the  lamp  holder  to 
disconnect from the lamp end. Turn on the water supply to check for leaks before 
reconnecting the electric supply.  

 

Important:  

The plastic body and blue compression fittings have been manufactured from polymers that 
have been specifically stabilised to protect them from the effects of the UVC emitted from 
the UV lamps. Despite this UV protection they will be eroded by a combination of the UVC 
and water flow. As a matter of course they should be inspected whenever a lamp change 
is carried out, to ensure they are not showing excessive wear and tear. Replacement parts 
are available.

 

 

6.  DISPOSAL OF ELECTRICAL/ELECTRONIC EQUIPMENT

 

 
 

DO NOT dispose of this product as an unsorted municipal waste. 

 
 

This  symbol  on  the  product  or  on  the  packaging  indicates  that  this  product  should  not  be  treated  as 
household waste.  Instead it should be handed over to the applicable collection point for the recycling of 
electrical and electronic equipment. 

 

 

 
By ensuring this product is disposed of correctly you will help prevent potential 
negative  consequences  for  the  environment  and  human  health,  which  could 
otherwise  be  caused  by  inappropriate  waste  handling  of  this  product.    The 
recycling of materials will help to conserve natural resources. 
 
For  more  information  please  contact  your  local  Civic  Office,  household  waste 
disposal service or the retailer where the product was purchased. 

 

 

7.  WARRANTY  

 

This product is guaranteed from the date of purchase against faulty workmanship and materials 
for: 

– 

two years within Europe 

– 

one year outside Europe 

 

  The manufacturer will replace or repair, at its discretion, any faulty units or components returned 

to the Company for inspection. 

  Proof of purchase may be required. 

  The manufacturer will not be liable in cases of incorrect installation of the  product, inappropriate 

use or neglect. 

  Any damages occurred due to shipping must be reported within 48 hours of receipt of the product. 

Any  claims  after  this  time  will  be  considered  as misuse  or  abuse  of the product  and  will  not  be 
covered by the warranty.

 

  The guarantee does not include serviceable parts, i.e. lamps, quartz sleeves and O-rings, etc. 

 

Summary of Contents for QUANTUM CLASSIC Q-65

















Reviews: