You can delete the code of a call or acknowledge-
ment transmitter you no longer need from the call
signaller as follows:
1. Keep both buttons on the call signaller
depressed at the same time until these start
blinking rapidly and the device will play an
acknowledgement signal.
2. Press the button of the transmitter until both
buttons are lit on the call signaller and the
acknowledgement beep sounds. The
transmitter was deleted. Proceed accordingly
to delete additional transmitters. If you do not
push a transmitter button within 20 seconds,
the call signaller switches automatically to
standby.
If you want to delete all saved transmitters,
proceed as described in the section "Restoring
the factory settings".
or
or
Reset to Default Settings
(RESET)
> 1,6 s
within
20 s
within
20 s
This function serves to transmit the coding of an
acknowledgement transmitter to the call
signaller.
1. Press the button Q until it blinks and the
device will play an acknowledgement signal.
If you want to cancel the teach-in process,
briefly press the button Q again.
2. Press the button of the acknowledgement
transmitter which you want to use to
acknowledge the call within 20 seconds until
the button Q of the call signaller lights up.
After approx. 4 seconds, you can teach in
additional acknowledgement transmitters.
If there is no input within 20 seconds, the call
signaller switches automatically to standby.
You can save at most 32 acknowledgement calls.
If all 32 memory slots are occupied, you will hear
a warning sound for approx. 2 seconds when
receiving another send code.
In case of a call by a call transmitter that was
already taught in, the teach-in process cannot be
activated.
Attention!
It is not possible to teach in an already
taught in acknowledgement transmitter as call
transmitter.
Teaching in acknowledgement transmitter
You can turn off (acknowledge) the call signal
and the flashlight with the buttons R or Q or by
pressing a button on the acknowledgement
transmitter.
Acknowledging a call
Selecting the melody
This function serves to transmit the coding of the
call transmitter to the call signaller.
1. Press the button R until it blinks and the
device will play an acknowledgement signal. If
you want to cancel the teach-in process,
briefly press the button R again.
2. Press the button of the call transmitter within
20 seconds. If there is no input within 20
seconds, the call signaller switches
automatically to standby
If the coding was transferred, the button R is lit
for approx. 4 seconds. Afterwards you can
teach in additional call transmitters
In case of a call by a call transmitter that was
already taught in, the teach-in process cannot be
activated.
Attention!
It is not possible to teach in an already
taught in call transmitter as acknowledgement
transmitter.
You can save at most 32 call transmitters. If all 32
memory slots are occupied, you will hear a
warning sound for approx. 2 seconds when
receiving another send code.
Teaching in the call transmitter
> 1,6 s
4 s
4 s
Setting the volume/flashlight
1. Briefly (<1.6 s) press the button Q. The
currently selected melody is played back at
the current volume.
2. Press the button Q again once the melody
has stopped. Now the device switches to the
next volume/flashlight combination.
If you do not press the button Q once again,
the selection is applied once the ring tone and
the blinking stop.
Loud +
flashing
light
Mute
Quiet
(no flashing
light)
Loud (no
flashing
light)
Quiet +
flashing
light
< 1,6 s
Press the
button Q
repeatedly
until the
desired
combination is
played.
Select the desired melody by pressing the button
R repeatedly
You have to wait until the selected melody stops
before you can select the next melody.
ca. 1,6 s
Attention!
With a RESET all memorized call
and acknoledgement transmitters
1.
2.
as well as all
relevant settings are deleted and factory settings
are activated.
Keep both buttons on the call signaller
depressed at the same time until these start
blinking rapidly and the device will play an
acknowledgement signal.
Press both buttons again. It sounds the
acknowledgement beep and both bottuns
lights approx. 4 seconds. The call signaller
was return to factory settings.
> 1,6 s
> 1,6 s
To cancel press a button
To cancel press a button
1.
2.
3.
Westminster
March
Ring Bell
Deleting individual transmitters
Troubleshooting
Press the button
R repeatedly
until the desired
melody is
played.
1.
Westminster
- The button R or Q blinks rapidly and the
warning beep sounds for 2 seconds: You have
tried to teach in an already taught in call
transmitter as acknowledgement transmitter or
an already taught in acknowledgement
transmitter as call transmitter.
- Warning beep for 2 seconds when teaching in a
call or acknowledgement transmitter: All
memory slots are occupied. Delete individual
transmitters and repeat the teaching in
process.
Disposal
Conformity
Customer Service
Put the packaging material into the
recycling bins for cardboard, paper and
plastics.
Dispose of the waste product via a collec-
tion point for electronic scrap or via your
specialist dealer.
Waste electrical products should not be
disposed of with household waste!
Hereby, ELDAT GmbH declares that the radio
equipment type RCP090 is in compliance with
Directive 2014/53/EU.
The full text of the EU declaration of conformity
is available at the following internet address:
www.eldat.de
For use in: EU/CH/FL/IS/N
Warranty
We will remedy defects on the device based on
material or production errors within the statutory
warranty period or exchange the device.
Any unauthorized tampering with, or modifica-
tions to, the product shall render this warranty null
and void.
General Information
If the device does not work properly despite
proper handing or in case of damage, please
contact your retailer.
